Author Topic: Another Carlton bar ?  (Read 314 times)

0 Members and 0 Guests are viewing this topic.

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2108
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Another Carlton bar ?
« Reply #10 on: September 11, 2016, 05:01:22 am »
Mike I am interested in NOS Windsor Speed Tip bars.  Large Husky, small Husky, and also old Poulan Homelite and Mac mounts.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline mdavlee .

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1968
  • Karma: 171
Re: Another Carlton bar ?
« Reply #11 on: September 11, 2016, 07:08:25 am »
There's a 24" hanging up and a 20" I think. 24 I want to say is large husky. 20 may be mid stihl. I'll be there this week picking up parts again on Friday.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21766
  • Karma: 517
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2108
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Another Carlton bar ?
« Reply #13 on: October 23, 2016, 08:50:36 pm »
There's a 24" hanging up and a 20" I think. 24 I want to say is large husky. 20 may be mid stihl. I'll be there this week picking up parts again on Friday.

Sorry I didn't reply earlier.  Haven't been on the board in a while, and still not getting notifications.

I'm interested in the 24" large Husky bar.  Not in a hurry for it.  Whenever you get by there again....
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21766
  • Karma: 517
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Another Carlton bar ?
« Reply #14 on: October 24, 2016, 02:24:09 pm »
There's a 24" hanging up and a 20" I think. 24 I want to say is large husky. 20 may be mid stihl. I'll be there this week picking up parts again on Friday.

Sorry I didn't reply earlier.  Haven't been on the board in a while, and still not getting notifications.

I'm interested in the 24" large Husky bar.  Not in a hurry for it.  Whenever you get by there again....

We figured this out with 3000 FPS Roger's help. He had same email provider as you. He didnt receive notifications.   Ask tech and he said same thing that those folks block notices. Roger changed his email to one of his others and he got notifications then.
REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2108
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Another Carlton bar ?
« Reply #15 on: October 24, 2016, 05:25:35 pm »
Hmm.  I'll have to switch my email address here to my gmail account.  Hardly use that one for anything...
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

 

Related Topics

  Subject / Started by Replies Last post
1 Replies
1040 Views
Last post November 28, 2011, 11:44:35 am
by bloodontheice
5 Replies
528 Views
Last post June 08, 2014, 06:46:27 pm
by man of stihl
0 Replies
136 Views
Last post April 30, 2016, 09:48:31 am
by Cut4fun .
3 Replies
2165 Views
Last post February 11, 2017, 03:39:09 pm
by Cut4fun .
22 Replies
230 Views
Last post November 24, 2017, 11:25:16 am
by Philbert