Author Topic: Chainsaw Chain Grinder Wheels  (Read 929 times)

0 Members and 0 Guests are viewing this topic.

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4477
  • Karma: 275
  • Location: Carpenter, Wyoming
Re: Chainsaw Chain Grinder Wheels
« Reply #30 on: August 09, 2014, 09:42:11 pm »
I usually just blow my chains off with compressed air before grinding.   Thought about using the ultra sonic but I have not tried it yet.   
PP 505, 475, 445.

Offline Philbert

  • Gas Hotsaw
  • ******
  • Posts: 557
  • Karma: 75
Re: Chainsaw Chain Grinder Wheels
« Reply #31 on: August 09, 2014, 10:06:01 pm »
Probably already posted this somewhere here on CR ('CSR'?)

If a chain is pretty clean, I might just wipe/brush off excess oil or light dirt/wood chips, etc.  A lot of the chains I get, scrounge, or accept into Philbert's 'No-Kill-Chain-Shelter' are pretty grungy.  On some, I can't read the markings.  And often, they have defects (rust, burrs, **** links, loose rivets, improvised repairs, upside down/inside out tie straps, etc.) hidden by gunk.  I like to fix these before sharpening, and to keep the gunk out of the grinding wheels.

- I dip the dirty chains in a commercial, water-based degreaser with lye (sodium hydroxide).  'Super Clean' is one brand I use.  Note that not all 'purple cleaners' have the sodium hydroxide, which makes a big difference, so read the label. 10 - 15 seconds is all that is needed sometimes.

- Brush lightly with an old toothbrush, in the bottom of the laundry tub, wearing gloves, and splash goggles.  Repeat if necessary.

- Rinse well in clean water.

- Dry on an old, garage sale cookie sheet for 15 to 20 minutes at 200*F to remove any water and prevent rusting.

- Since this removes all the lubrication, I re-lube after sharpening with a heavy coat of WD-40, since this is thin and penetrates well around the rivets.  I have another old baking pad with an absorbent pad in the bottom I use for this.  Brush the WD-40 on with another old toothbrush, and run the chain over a dowel to make sure that all the links are free and lubricated.

Sounds like a lot, but I try to clean/sharpen chains in batches, so not much time per chain.  I tried the USC, and that works, but it takes longer and is harder to clean afterwards IMO.

Philbert

Offline Philbert

  • Gas Hotsaw
  • ******
  • Posts: 557
  • Karma: 75
Re: Chainsaw Chain Grinder Wheels
« Reply #32 on: August 30, 2014, 11:02:21 pm »
Got the Bailey's/Molemab wheel (Left) to compare with the Tilton/Total wheel (Right)! Look identical Cost was almost half.
The Molemab wheel is brand new. The Total wheel has been used on about 15 chains - wear is not noticeable.

Philbert


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22117
  • Karma: 550
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Chainsaw Chain Grinder Wheels
« Reply #33 on: August 30, 2014, 11:18:14 pm »
Got the Bailey's/Molemab wheel (Left) to compare with the Tilton/Total wheel (Right)! Look identical Cost was almost half.
The Molemab wheel is brand new. The Total wheel has been used on about 15 chains - wear is not noticeable.

Philbert



Good to know. Thanks for all the digging in and up on this stuff.
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
29 Replies
5285 Views
Last post September 25, 2016, 11:18:04 am
by HolmenTree
7 Replies
720 Views
Last post October 17, 2018, 03:16:42 pm
by woodripper
23 Replies
890 Views
Last post April 06, 2013, 10:43:46 am
by davbell22602
6 Replies
1296 Views
Last post October 19, 2015, 02:21:03 pm
by Cut4fun .
6 Replies
1151 Views
Last post February 22, 2020, 08:37:20 am
by Cut4fun
15 Replies
1053 Views
Last post November 13, 2013, 05:16:52 pm
by 660magnum
24 Replies
585 Views
Last post September 04, 2015, 12:42:20 pm
by Cut4fun .
9 Replies
212 Views
Last post March 23, 2016, 12:29:47 am
by 660magnum
6 Replies
180 Views
Last post December 02, 2017, 03:51:48 pm
by Cut4fun .
3 Replies
40 Views
Last post October 10, 2020, 07:17:47 am
by Cut4fun