« previous next »
Pages: 1 [2]   Go Down

Author Topic: 24" D009 D176 bars 81DL 84DL  (Read 779 times)

0 Members and 0 Guests are viewing this topic.

Offline Chris-PA

  • 6 cube
  • ****
  • Posts: 209
  • Karma: 32
Re: 24" D009 D176 bars 81DL 84DL
« Reply #10 on: March 25, 2016, 05:24:35 pm »
Quote from: SawTroll on March 24, 2016, 11:18:42 pm
Btw, it is the adjuster pin vs. the crank that really matters, not the studs.
I guess that depends on if it is running out of adjuster screw travel or the bar slot is bottomed out on the stud.  I'm not sure which is happening here.  If it's the adjuster screw then perhaps you could add another hole?
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23515
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 24" D009 D176 bars 81DL 84DL
« Reply #11 on: March 25, 2016, 06:43:26 pm »
This one is running out of adjuster travel.  I have just drilled a hole further back in the past on my own stuff. ;) = redneck fix.
Logged

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2117
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northwestern Wyoming
Re: 24" D009 D176 bars 81DL 84DL
« Reply #12 on: March 30, 2016, 07:40:17 pm »
I have 81DL D176 and 84DL D009 bars.  Compared them a few years ago.  Like Chris said, I think they were about 1" different in length.  From what I remember (can't bank on my memory too much), 82DL was about right when trying a D009 mount bar on a D176 mount saw (and 71DL was 'about right' for a 20" 72DL D009 bar on a D176 saw in place of a 70DL 20" bar).

Now to bank WAY too much on my memory...........................if I can get to the shop this weekend I'll take a pic of a D009 mount 24" bar next to a D176 mount 24" bar.  That's assuming I don't forget by then......
Logged
Informative Informative x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23515
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 24" D009 D176 bars 81DL 84DL
« Reply #13 on: March 30, 2016, 08:01:56 pm »
Cool. Thanks and good to see you around.
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23515
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 24" D009 D176 bars 81DL 84DL
« Reply #14 on: April 08, 2016, 08:24:53 pm »
Broke the 84DL chain and took the WAG.

Went with 82DL with D009 bar and it was perfect on the echo 702 d176 mount saw.
Logged

Offline sharkey

  • Piped Saw
  • *****
  • Posts: 368
  • Karma: 37
Re: 24" D009 D176 bars 81DL 84DL
« Reply #15 on: April 12, 2016, 04:20:49 pm »
Just an idea for you guys trying to fit the HVA bar to the MAC or Echo.  A piece of 3/8OD metal fuel line, brake line or plumbing line has a 5/16ID.  Cut a 1/4 inch piece with a pipe cutter and slide it over the stud.  You can harden your new adapters with a propane torch and some oil if your serious.  Now you can fit both bar sizes by sliding the 3/8 - 5/16 adapters on and off the bar studs. 
Logged
Informative Informative x 1 View List
Pages: 1 [2]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
2 Replies
589 Views 		Last post February 22, 2014, 05:47:21 pm
by Gregg MacPherson
6 Replies
563 Views 		Last post November 08, 2014, 09:59:01 pm
by Cut4fun .
6 Replies
354 Views 		Last post February 08, 2015, 05:51:03 pm
by Eccentric
22 Replies
1324 Views 		Last post August 24, 2015, 08:50:24 pm
by Eccentric
4 Replies
238 Views 		Last post April 27, 2015, 12:01:09 pm
by Cut4fun .
5 Replies
487 Views 		Last post April 15, 2016, 09:09:13 pm
by SawTroll
1 Replies
229 Views 		Last post July 08, 2019, 11:14:45 am
by Cut4fun .
2 Replies
229 Views 		Last post October 05, 2020, 07:27:30 am
by Cut4fun
2 Replies
176 Views 		Last post August 19, 2020, 08:08:32 am
by Cut4fun
0 Replies
93 Views 		Last post October 25, 2020, 07:42:34 am
by Cut4fun