Author Topic: Chainsaw Chain Grinder Wheels  (Read 2010 times)

0 Members and 1 Guest are viewing this topic.

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4706
  • Karma: 320
  • Location: Carpenter, Wyoming

  • Total Badges: 43
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 7 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary
Re: Chainsaw Chain Grinder Wheels
« Reply #30 on: August 09, 2014, 09:42:11 pm »
I usually just blow my chains off with compressed air before grinding.   Thought about using the ultra sonic but I have not tried it yet.   
PP 505, 475, 445.

Offline Philbert

  • Gas Hotsaw
  • ******
  • Posts: 563
  • Karma: 76

  • Total Badges: 23
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Level 5 Fifth year Anniversary 500 Posts Fourth year Anniversary
Re: Chainsaw Chain Grinder Wheels
« Reply #31 on: August 09, 2014, 10:06:01 pm »
Probably already posted this somewhere here on CR ('CSR'?)

If a chain is pretty clean, I might just wipe/brush off excess oil or light dirt/wood chips, etc.  A lot of the chains I get, scrounge, or accept into Philbert's 'No-Kill-Chain-Shelter' are pretty grungy.  On some, I can't read the markings.  And often, they have defects (rust, burrs, **** links, loose rivets, improvised repairs, upside down/inside out tie straps, etc.) hidden by gunk.  I like to fix these before sharpening, and to keep the gunk out of the grinding wheels.

- I dip the dirty chains in a commercial, water-based degreaser with lye (sodium hydroxide).  'Super Clean' is one brand I use.  Note that not all 'purple cleaners' have the sodium hydroxide, which makes a big difference, so read the label. 10 - 15 seconds is all that is needed sometimes.

- Brush lightly with an old toothbrush, in the bottom of the laundry tub, wearing gloves, and splash goggles.  Repeat if necessary.

- Rinse well in clean water.

- Dry on an old, garage sale cookie sheet for 15 to 20 minutes at 200*F to remove any water and prevent rusting.

- Since this removes all the lubrication, I re-lube after sharpening with a heavy coat of WD-40, since this is thin and penetrates well around the rivets.  I have another old baking pad with an absorbent pad in the bottom I use for this.  Brush the WD-40 on with another old toothbrush, and run the chain over a dowel to make sure that all the links are free and lubricated.

Sounds like a lot, but I try to clean/sharpen chains in batches, so not much time per chain.  I tried the USC, and that works, but it takes longer and is harder to clean afterwards IMO.

Philbert

Offline Philbert

  • Gas Hotsaw
  • ******
  • Posts: 563
  • Karma: 76

  • Total Badges: 23
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Level 5 Fifth year Anniversary 500 Posts Fourth year Anniversary
Re: Chainsaw Chain Grinder Wheels
« Reply #32 on: August 30, 2014, 11:02:21 pm »
Got the Bailey's/Molemab wheel (Left) to compare with the Tilton/Total wheel (Right)! Look identical Cost was almost half.
The Molemab wheel is brand new. The Total wheel has been used on about 15 chains - wear is not noticeable.

Philbert


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23706
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

  • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Chainsaw Chain Grinder Wheels
« Reply #33 on: August 30, 2014, 11:18:14 pm »
Got the Bailey's/Molemab wheel (Left) to compare with the Tilton/Total wheel (Right)! Look identical Cost was almost half.
The Molemab wheel is brand new. The Total wheel has been used on about 15 chains - wear is not noticeable.

Philbert



Good to know. Thanks for all the digging in and up on this stuff.

 

Related Topics

  Subject / Started by Replies Last post
8 Replies
1382 Views
Last post May 09, 2023, 09:30:13 am
by Cut4fun .
6 Replies
2222 Views
Last post October 19, 2015, 02:21:03 pm
by Cut4fun .
10 Replies
2590 Views
Last post January 28, 2021, 10:31:35 pm
by Elden
15 Replies
1994 Views
Last post November 13, 2013, 05:16:52 pm
by 660magnum
1 Replies
297 Views
Last post March 28, 2014, 07:39:06 pm
by Cut4fun .
24 Replies
1496 Views
Last post September 04, 2015, 12:42:20 pm
by Cut4fun .
9 Replies
558 Views
Last post March 23, 2016, 12:29:47 am
by 660magnum
6 Replies
747 Views
Last post December 02, 2017, 03:51:48 pm
by Cut4fun .
4 Replies
559 Views
Last post September 29, 2023, 11:15:59 am
by Cut4fun .
0 Replies
271 Views
Last post November 09, 2022, 06:05:52 am
by Cut4fun .