Author Topic: Oregon Pro Lite / Husky Techlite  (Read 111 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 19962
  • Karma: 418
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Oregon Pro Lite / Husky Techlite
« on: November 10, 2014, 04:11:20 pm »
Trying to find out what the weight difference really is between a oregon prolite and a husky tech lite. For small saws like 338 540 only.

Oregon pro lite 12" - 16"   http://www.oregonproducts.com/pro/products/bars/pro_91_91Intenz.htm




Just dont see where this tech lite could be much lighter then pro lite.

They say saves 18% of the regular bars.  But nothing comparing to a pro-lite bar.



REDNECK Saw Repair Getter Done

Social Buttons


Offline fuzz1500

  • 4 cube
  • **
  • Posts: 35
  • Karma: 5
Re: Oregon Pro Lite / Husky Techlite
« Reply #1 on: February 10, 2015, 09:35:09 pm »
Ive wondered the same . Have never had a Techlite yet . Mostly cuz Im cheap !!!

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2105
  • Karma: 215
  • Magnesium and Iron.
  • Location: Northern California.
Re: Oregon Pro Lite / Husky Techlite
« Reply #2 on: February 16, 2015, 02:53:59 pm »
I've only handled one of the small mount Techlite bars.  Was on a 540XPT at the dealer.  16" IIRC.  Felt a bit less nose heavy than a 'regular' laminated bar (such as a ProLite) on similar tophandles.  I was wanting to put a 28" Techlite on my 272XP..............................but hadn't yet gotten over the cost (and then they stopped selling them).
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

 

Related Topics

  Subject / Started by Replies Last post
75 Replies
5452 Views
Last post March 12, 2017, 08:11:21 pm
by Eccentric
13 Replies
565 Views
Last post April 21, 2016, 01:26:35 pm
by SawTroll
4 Replies
211 Views
Last post August 12, 2013, 10:10:23 pm
by Cut4fun
1 Replies
174 Views
Last post August 22, 2013, 05:40:20 pm
by Cut4fun .
4 Replies
372 Views
Last post August 31, 2013, 09:12:44 pm
by mdavlee .
14 Replies
1322 Views
Last post January 25, 2018, 09:12:57 pm
by Philbert
4 Replies
87 Views
Last post November 09, 2014, 07:03:40 pm
by mdavlee .
11 Replies
334 Views
Last post March 05, 2015, 11:56:39 am
by 660magnum
0 Replies
53 Views
Last post May 27, 2017, 12:13:28 pm
by Cut4fun .
3 Replies
56 Views
Last post November 27, 2017, 08:58:58 am
by AmericanPsycho