Author Topic: short hard nose bars  (Read 204 times)

0 Members and 0 Guests are viewing this topic.

Offline dannyupsolate

  • Piped Saw
  • *****
  • Posts: 328
  • Karma: 28
short hard nose bars
« on: October 25, 2015, 08:26:17 pm »
been junking some small poulan factory bars today eat up tips. found some short hardnose bars 14 and 16 inch any disadvantage to using them on wildthing class saws.

Share on Facebook Share on Twitter


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22015
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: short hard nose bars
« Reply #1 on: October 25, 2015, 08:30:48 pm »
Had a bunch of them too. I dont know where they have went but no biggie. 

Usually the banana nose style.
REDNECK Saw Repair Getter Done

Offline dannyupsolate

  • Piped Saw
  • *****
  • Posts: 328
  • Karma: 28
Re: short hard nose bars
« Reply #2 on: October 25, 2015, 10:00:20 pm »
have any  of you used hard nose bars on these small saws and how well did it work out.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22015
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: short hard nose bars
« Reply #3 on: October 26, 2015, 11:13:52 am »
They came on the small saws 10" 12" etc and up. I used them a on them and they were fine.
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22015
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: short hard nose bars
« Reply #4 on: October 26, 2015, 11:16:18 am »
Front little poulan XX came with one.

REDNECK Saw Repair Getter Done

Offline dannyupsolate

  • Piped Saw
  • *****
  • Posts: 328
  • Karma: 28
Re: short hard nose bars
« Reply #5 on: October 26, 2015, 01:06:41 pm »
so if customer questions the hard nose bar just tell them they will love it.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22015
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: short hard nose bars
« Reply #6 on: October 26, 2015, 01:34:50 pm »
Just make sure they run the chain alittle looser.  Dont tighten it up so tight like they do.

Good for trenching and root cutting too.  ;D
REDNECK Saw Repair Getter Done

Offline dannyupsolate

  • Piped Saw
  • *****
  • Posts: 328
  • Karma: 28
Re: short hard nose bars
« Reply #7 on: October 26, 2015, 04:51:37 pm »
thanks I have never used one. they look like they might be tougher than these new oem bars

Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2753
  • Karma: 170
Re: short hard nose bars
« Reply #8 on: October 26, 2015, 08:25:26 pm »
I have the same 14" hard nose bar on a Poulan s-25 that was on it when I bought the saw new .Now I know I've went through at least 25 chains on that thing since the mid 70's .Bar is still fine but I've dressed it on a belt sander several times in all those years .

Saw is fine too .I ran that thing over 30 years before I had to rebuild the carb.

Offline dannyupsolate

  • Piped Saw
  • *****
  • Posts: 328
  • Karma: 28
Re: short hard nose bars
« Reply #9 on: October 26, 2015, 08:31:35 pm »
much tougher than newer roller tips then just pitched 4 in scrap pile all dished out right behind roller. oem bars

 

Related Topics

  Subject / Started by Replies Last post
1 Replies
186 Views
Last post November 07, 2012, 10:27:43 pm
by Roanoker494
0 Replies
58 Views
Last post October 14, 2013, 10:34:47 am
by bloodontheice
1 Replies
165 Views
Last post November 05, 2013, 12:38:23 am
by Eccentric
0 Replies
114 Views
Last post February 02, 2014, 10:29:09 pm
by aclarke
3 Replies
133 Views
Last post May 02, 2014, 02:00:06 pm
by Eccentric
6 Replies
530 Views
Last post May 30, 2014, 08:24:23 pm
by Billyram
7 Replies
149 Views
Last post May 18, 2015, 10:48:32 pm
by old guy
7 Replies
249 Views
Last post July 23, 2015, 02:27:35 pm
by Jason K
29 Replies
470 Views
Last post April 25, 2017, 08:27:24 am
by chy_farm
0 Replies
74 Views
Last post January 05, 2019, 06:59:31 pm
by trappermike