« previous next »
Pages: [1]   Go Down

Author Topic: short hard nose bars  (Read 747 times)

0 Members and 0 Guests are viewing this topic.

Offline dannyupsolate

  • Piped Saw
  • *****
  • Posts: 328
  • Karma: 28
short hard nose bars
« on: October 25, 2015, 08:26:17 pm »
been junking some small poulan factory bars today eat up tips. found some short hardnose bars 14 and 16 inch any disadvantage to using them on wildthing class saws.
Logged

Share on Facebook Share on Twitter

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23987
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: short hard nose bars
« Reply #1 on: October 25, 2015, 08:30:48 pm »
Had a bunch of them too. I dont know where they have went but no biggie. 

Usually the banana nose style.
Logged

Offline dannyupsolate

  • Piped Saw
  • *****
  • Posts: 328
  • Karma: 28
Re: short hard nose bars
« Reply #2 on: October 25, 2015, 10:00:20 pm »
have any  of you used hard nose bars on these small saws and how well did it work out.
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23987
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: short hard nose bars
« Reply #3 on: October 26, 2015, 11:13:52 am »
They came on the small saws 10" 12" etc and up. I used them a on them and they were fine.
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23987
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: short hard nose bars
« Reply #4 on: October 26, 2015, 11:16:18 am »
Front little poulan XX came with one.

Logged

Offline dannyupsolate

  • Piped Saw
  • *****
  • Posts: 328
  • Karma: 28
Re: short hard nose bars
« Reply #5 on: October 26, 2015, 01:06:41 pm »
so if customer questions the hard nose bar just tell them they will love it.
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23987
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: short hard nose bars
« Reply #6 on: October 26, 2015, 01:34:50 pm »
Just make sure they run the chain alittle looser.  Dont tighten it up so tight like they do.

Good for trenching and root cutting too.  ;D
Logged

Offline dannyupsolate

  • Piped Saw
  • *****
  • Posts: 328
  • Karma: 28
Re: short hard nose bars
« Reply #7 on: October 26, 2015, 04:51:37 pm »
thanks I have never used one. they look like they might be tougher than these new oem bars
Logged

Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2779
  • Karma: 181
Re: short hard nose bars
« Reply #8 on: October 26, 2015, 08:25:26 pm »
I have the same 14" hard nose bar on a Poulan s-25 that was on it when I bought the saw new .Now I know I've went through at least 25 chains on that thing since the mid 70's .Bar is still fine but I've dressed it on a belt sander several times in all those years .

Saw is fine too .I ran that thing over 30 years before I had to rebuild the carb.
Logged

Offline dannyupsolate

  • Piped Saw
  • *****
  • Posts: 328
  • Karma: 28
Re: short hard nose bars
« Reply #9 on: October 26, 2015, 08:31:35 pm »
much tougher than newer roller tips then just pitched 4 in scrap pile all dished out right behind roller. oem bars
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
6 Replies
667 Views 		Last post January 20, 2016, 02:18:40 pm
by Cut4fun .
Roller nose

Started by EHP Wanted

0 Replies
293 Views 		Last post February 20, 2012, 10:19:32 pm
by EHP
0 Replies
236 Views 		Last post October 14, 2013, 10:34:47 am
by bloodontheice
0 Replies
301 Views 		Last post January 01, 2014, 07:28:04 pm
by stihls066
0 Replies
305 Views 		Last post February 02, 2014, 10:29:09 pm
by aclarke
3 Replies
401 Views 		Last post May 02, 2014, 02:00:06 pm
by Eccentric
7 Replies
973 Views 		Last post July 23, 2015, 02:27:35 pm
by Jason K
29 Replies
1754 Views 		Last post April 25, 2017, 08:27:24 am
by chy_farm
5 Replies
631 Views 		Last post July 31, 2017, 07:55:29 pm
by mdavlee .
0 Replies
327 Views 		Last post January 05, 2019, 06:59:31 pm
by trappermike