Author Topic: Whats on your bench today  (Read 19323 times)

0 Members and 96 Guests are viewing this topic.

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4706
  • Karma: 320
  • Location: Carpenter, Wyoming

  • Total Badges: 43
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 7 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary
Re: Whats on your bench today
« Reply #320 on: November 20, 2015, 12:56:16 pm »
Had a little poulan (havent opened poulan case) dropped off today.    Guy brought it in from a deer camp and said had a local professional dealer  check it over and couldnt get it to start either.

I like the challenge.  ;D ;)

Man I will laugh if this was something so simple to see.

It just makes you feel good fixing something for someone that others either could not figure out or did not want to take the time to figure out.
PP 505, 475, 445.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23708
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

  • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Whats on your bench today
« Reply #321 on: November 20, 2015, 06:51:35 pm »
Had a little poulan (havent opened poulan case) dropped off today.    Guy brought it in from a deer camp and said had a local professional dealer  check it over and couldnt get it to start either.

I like the challenge.  ;D ;)

Man I will laugh if this was something so simple to see.

It just makes you feel good fixing something for someone that others either could not figure out or did not want to take the time to figure out.

I peeked in the case before going out to eat. Looked like a brand new strato poulan 3314 in there

Offline dutchsawdoctor

  • Gas Hotsaw
  • ******
  • Posts: 582
  • Karma: 45
  • Love repairing old saws
  • Location: Netherlands Flevoland
    • Saul's kettingzagen site

  • Total Badges: 27
    Badges: (View All)
    Fourth year Anniversary Apple User Mobile User 500 Posts Third year Anniversary Second year Anniversary
Re: Whats on your bench today
« Reply #322 on: November 28, 2015, 12:42:45 am »
the solo twin is back on the bench >:(

one cilinder wont pic up, it only wont to pic up at higher rev. but it has spark all the way spark plug net 225 from Beru

both cilinder puls 130 psi, gone split the crank case to see whats went wrong there, owner had it overhauld with new seals, but lots off screws i found where lose :o

Saul

finaly i hve now time to work on this twin,( head to much work to do doing 60"s in a week ::) )

i have to pull the clutch of and then the starter recoil

Saul
Best regards,Saul
Dolmar  Stihl Solo Husqvarna Homelite Ole-mac Echo Jobu Ridgid Poulan Remington Pioneer Partner ,Danarm stanley
more chainsaw repairs Oldtimer-Motorsägen  http://pily.strojevlese.cz / http://www.sauls-kettingzagen-site.nl

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4706
  • Karma: 320
  • Location: Carpenter, Wyoming

  • Total Badges: 43
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 7 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary
Re: Whats on your bench today
« Reply #323 on: November 28, 2015, 12:53:30 pm »
the solo twin is back on the bench >:(

one cilinder wont pic up, it only wont to pic up at higher rev. but it has spark all the way spark plug net 225 from Beru

both cilinder puls 130 psi, gone split the crank case to see whats went wrong there, owner had it overhauld with new seals, but lots off screws i found where lose :o

Saul

finaly i hve now time to work on this twin,( head to much work to do doing 60"s in a week ::) )

i have to pull the clutch of and then the starter recoil

Saul

60 hours a week does not leave much time for playing.  The twin will be worth it when done.
PP 505, 475, 445.

Offline dutchsawdoctor

  • Gas Hotsaw
  • ******
  • Posts: 582
  • Karma: 45
  • Love repairing old saws
  • Location: Netherlands Flevoland
    • Saul's kettingzagen site

  • Total Badges: 27
    Badges: (View All)
    Fourth year Anniversary Apple User Mobile User 500 Posts Third year Anniversary Second year Anniversary
Re: Whats on your bench today
« Reply #324 on: November 29, 2015, 03:26:34 am »
the solo twin is back on the bench >:(

one cilinder wont pic up, it only wont to pic up at higher rev. but it has spark all the way spark plug net 225 from Beru

both cilinder puls 130 psi, gone split the crank case to see whats went wrong there, owner had it overhauld with new seals, but lots off screws i found where lose :o

Saul

finaly i hve now time to work on this twin,( head to much work to do doing 60"s in a week ::) )

i have to pull the clutch of and then the starter recoil

Saul

60 hours a week does not leave much time for playing.  The twin will be worth it when done.
Right about that ;D, ordered for my self a new puller-set to get that clutch of ;)

Saul
Best regards,Saul
Dolmar  Stihl Solo Husqvarna Homelite Ole-mac Echo Jobu Ridgid Poulan Remington Pioneer Partner ,Danarm stanley
more chainsaw repairs Oldtimer-Motorsägen  http://pily.strojevlese.cz / http://www.sauls-kettingzagen-site.nl

Offline jmester

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2106
  • Karma: 171
  • Location: MD

  • Total Badges: 36
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Level 6
Re: Whats on your bench today
« Reply #325 on: November 29, 2015, 09:04:24 pm »
Have a Husqvarna 580 BTS back back blower. Needs pto side bearing and a pto case half as the mounting ears are ****.
FEAR NO TREE. FEAR GOD.

Offline weimedog

  • 6 cube
  • ****
  • Posts: 260
  • Karma: 57

  • Total Badges: 25
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Level 5 Linux User Mobile User
Re: Whats on your bench today
« Reply #326 on: December 17, 2015, 08:32:42 am »
A smashed MS391, a Dirty MS290, a tuned too rich MS460, A Husqvarna 51 with a rotted fuel line, A toasted 562 and a 372X-torq with a wasted clutch side main bearing. Another 562 getting that latest release of ignition/carb and wiring. A Dolmar 120 with what looks like a tank vent rotted. A bearings up rebuild on a 385, Then my fun Projects hopefully. "Cyclops II" & a tweaked MS660.

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4706
  • Karma: 320
  • Location: Carpenter, Wyoming

  • Total Badges: 43
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 7 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary
Re: Whats on your bench today
« Reply #327 on: December 17, 2015, 10:01:56 am »
A smashed MS391, a Dirty MS290, a tuned too rich MS460, A Husqvarna 51 with a rotted fuel line, A toasted 562 and a 372X-torq with a wasted clutch side main bearing. Another 562 getting that latest release of ignition/carb and wiring. A Dolmar 120 with what looks like a tank vent rotted. A bearings up rebuild on a 385, Then my fun Projects hopefully. "Cyclops II" & a tweaked MS660.


You don't have enough to do.
PP 505, 475, 445.

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 150
  • Location: Hayesville, NC

  • Total Badges: 31
    Badges: (View All)
    Level 6 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary 1000 Posts Old Browser
Re: Whats on your bench today
« Reply #328 on: December 17, 2015, 10:55:25 pm »
2-346 OE doing AFM 44.3 PC on both.  1 needs clutch side seal which I don't have in stock, dont know about seals on the other.  Checked case screws on both they started tightening @ 3 nm.  I've started checking them on everything now.  2002 2159 Jred I just picked up started @ 4 nm.
Shep

Offline jmester

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2106
  • Karma: 171
  • Location: MD

  • Total Badges: 36
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Level 6
Re: Whats on your bench today
« Reply #329 on: December 17, 2015, 11:38:25 pm »
The couple 346 I have worked on the lean running condition came from loose cylinder base screws.
FEAR NO TREE. FEAR GOD.

 

Related Topics

  Subject / Started by Replies Last post
8 Replies
969 Views
Last post April 17, 2013, 07:51:59 pm
by Al Smith
7 Replies
1376 Views
Last post January 17, 2014, 01:45:22 pm
by Eccentric
41 Replies
2627 Views
Last post February 17, 2014, 01:18:38 pm
by Grande Dog
4 Replies
525 Views
Last post May 25, 2015, 03:12:51 pm
by 660magnum
3 Replies
1220 Views
Last post January 30, 2016, 09:59:03 am
by rburg
10 Replies
859 Views
Last post October 10, 2016, 06:47:42 pm
by 660magnum
0 Replies
1232 Views
Last post April 26, 2017, 08:51:22 pm
by dudechuck
3 Replies
685 Views
Last post February 12, 2018, 12:48:21 pm
by HolmenTree
3 Replies
554 Views
Last post April 21, 2019, 10:33:04 am
by 3000 FPS
0 Replies
144 Views
Last post December 05, 2022, 12:21:57 am
by FreakyLapidus