Author Topic: Baumr-AG 92 Chainsaw cover modification  (Read 192 times)

0 Members and 0 Guests are viewing this topic.

Offline aleksgavri

  • pruner
  • *
  • Posts: 4
  • Karma: 1
Baumr-AG 92 Chainsaw cover modification
« on: August 05, 2016, 04:47:50 am »
Hey,
I've just purchased a Baumr-AG 92cc and for a Chinese saw I can say that I am very happy. She's a little on the thirsty side however for someone who cuts 7-10 tonne of wood a year it certainly does the job. The link below will show you a MAJOR fault in the design system. The air filter is in the worst possible location and I wanted to know if anyone had any success in doing something similar? What has happened to others in the past is that the air intake is covered by a very cheap Chinese filter and eventually saw dust gets sucked up into the carburetor and into the crankcase (you can imagine it does wonders in there). So ideally easy access will mean that I can easily clean it without procrastination creeping in. What I wanted to do was cut the plastic cover and create a hinged door, any help is greatly appreciated!

https://www.youtube.com/watch?v=kY2GYT5SOGs - approx 2min 30sec into the video.

https://www.youtube.com/watch?v=kcNJDflngtU - what can potentially happen.

Social Buttons

Like Like x 1 View List

Offline Chris-PA

  • 6 cube
  • ****
  • Posts: 203
  • Karma: 28
Re: Baumr-AG 92 Chainsaw cover modification
« Reply #1 on: August 05, 2016, 02:03:37 pm »
Strange saw, with reeds even.  From other pictures it looks to have 1/2 of an A/V system.

As for the filter, on one hand there is a lot of stuff trapped on the filter, so you could almost say it was doing its job.  Perhaps with a bit of flashing clean up and some sealant between the halves (like I've done on other Chinese saw filters), and maybe some gasketing to the carb.  But not being able to get to it is a major issue, especially since it seems to have no effective pre-filtration system. 

Offline sharkey

  • Piped Saw
  • *****
  • Posts: 364
  • Karma: 36
Re: Baumr-AG 92 Chainsaw cover modification
« Reply #2 on: August 28, 2016, 08:02:43 am »
Anyone know what model copy this saw is of?

 

Related Topics

  Subject / Started by Replies Last post
0 Replies
233 Views
Last post April 02, 2011, 01:00:37 pm
by Cut4fun .
10 Replies
651 Views
Last post March 09, 2012, 03:38:49 pm
by Cut4fun .
1 Replies
215 Views
Last post March 12, 2012, 07:49:40 pm
by Modifiedmark
0 Replies
706 Views
Last post April 28, 2012, 09:46:37 am
by farmboy
0 Replies
235 Views
Last post July 22, 2012, 01:08:50 pm
by Cut4fun
32 Replies
1361 Views
Last post February 17, 2013, 03:02:04 am
by 3000 FPS
7 Replies
278 Views
Last post March 11, 2013, 08:03:33 pm
by 660magnum
4 Replies
50 Views
Last post June 19, 2014, 01:06:44 am
by 660magnum
12" bar guard/cover

Started by pigpen60 « 1 2 » Echo

16 Replies
525 Views
Last post August 19, 2014, 09:08:05 pm
by pigpen60
1 Replies
24 Views
Last post December 16, 2015, 06:44:27 pm
by Cut4fun