Author Topic: Power Products anyone? ah47 and the like..... whatcha got?????  (Read 2259 times)

0 Members and 1 Guest are viewing this topic.

Offline mcbob

  • 6 cube
  • ****
  • Posts: 261
  • Karma: -83
  • Location: Weston NSW Australia
Try a pair of new friction washers
I am a idiot so my pics disappeared.

Offline 1manband

  • Nitro Hotsaw
  • *******
  • Posts: 759
  • Karma: 52
Try a pair of new friction washers

thanks bob.  one of the two thick washers looks a little out of round?

here are the photos.



hiatus

Offline 1manband

  • Nitro Hotsaw
  • *******
  • Posts: 759
  • Karma: 52
hiatus

Offline 1manband

  • Nitro Hotsaw
  • *******
  • Posts: 759
  • Karma: 52
pawl and dogs have to go back orientated like this.........(at least for my clockwise motor running gear driven pto saw).
hiatus

Offline mcbob

  • 6 cube
  • ****
  • Posts: 261
  • Karma: -83
  • Location: Weston NSW Australia
much the same as the early Stihls with a friction washer set .... DONT oil them .......... Hmmmmmmmmmm no friction
I am a idiot so my pics disappeared.

Offline 1manband

  • Nitro Hotsaw
  • *******
  • Posts: 759
  • Karma: 52
........cleaned off all traces of grease and put it back together.  still slipping.  there is a pretty good lip wore in the cup like thing.

will get some new washers. 
hiatus

Offline mcbob

  • 6 cube
  • ****
  • Posts: 261
  • Karma: -83
  • Location: Weston NSW Australia
give the friction assy a good wash in white spirits or metho ............. never put oil or grease on them
I am a idiot so my pics disappeared.

Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2779
  • Karma: 181
I believe that type starter was refered to as the Fairbanks-Morse type. What a pain in the buttocks they can be .

Stihl went a step further and used a nylon insert in the flywheel for a more positive engagement .Fact I have either an 042 or an 048 with this device that surprisingly has never been a problem .

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2112
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northwestern Wyoming
I was recently given a Wards WD95 branded Mono with an AH81 engine.  FM starter is not engaging well.  Will get to that later.  Somebody welded a minibike clutch drum on top of the original saw drum so that they could drive a roller chain with it.  Didn't exactly get it squared well.  Will post a few pics when I get time.  There's still a throttle cable somewhat attached to the thing too.


Will be fun getting that clutch off.  Can't really reach the nut.  Will try knocking the bronze bushing out of the center of the minibike drum.  Hopefully that'll give enough clearance through the center to reach the nut with a socket.  If not...........I'll have to cut the snout of that drum off.

Will have to scare up a bar clamp and possibly bar studs for it.  IIRC, they were removed.  Hopefully I can make use of some parts from one of the other hulks I have....

 

Related Topics

  Subject / Started by Replies Last post
3 Replies
601 Views
Last post March 19, 2011, 12:14:49 am
by Kenskip1
6 Replies
972 Views
Last post April 21, 2012, 06:41:08 pm
by ed
1 Replies
1052 Views
Last post June 21, 2013, 02:06:14 pm
by brokenbudget
4 Replies
338 Views
Last post October 29, 2013, 05:01:05 pm
by Fish
5 Replies
454 Views
Last post July 19, 2014, 09:35:19 pm
by KilliansRedLeo
5 Replies
5980 Views
Last post July 23, 2014, 10:58:05 pm
by 660magnum
4 Replies
896 Views
Last post March 23, 2018, 07:27:14 pm
by deezlfan
2 Replies
247 Views
Last post November 02, 2019, 05:44:01 pm
by Husky141
6 Replies
387 Views
Last post January 07, 2021, 05:36:09 am
by Dave12
0 Replies
118 Views
Last post November 26, 2021, 09:39:08 am
by Cut4fun .