Author Topic: Jackson Alabama Racing  (Read 426 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22572
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Jackson ,Alabama
« Reply #10 on: November 03, 2011, 01:20:27 pm »
About 4hrs give or take.  Not to bad compared to where were going this weekend  lol

If it is close to 12hrs from here that makes it about 5-6hrs for you guys dont it?
REDNECK Saw Repair Getter Done

Offline Snoopy

  • 5 cube
  • ***
  • Posts: 128
  • Karma: 22
Re: Jackson ,Alabama
« Reply #11 on: November 03, 2011, 02:03:40 pm »
Its about 7.5-8 hours for us. Long drive but not as far as winnfield la. Its about a 10hr drive  :(

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4334
  • Karma: 189
  • OHIO REDNECK
Re: Jackson ,Alabama
« Reply #12 on: November 06, 2011, 11:39:21 am »
I forgot to check in with you on the drive back. How did it go?
REDNECK Saw Repair

Offline Snoopy

  • 5 cube
  • ***
  • Posts: 128
  • Karma: 22
Re: Jackson ,Alabama
« Reply #13 on: November 06, 2011, 12:20:50 pm »
Wayne had a big turn out for his show. All i remember is jody won the 3 cube. Jay got 5th in the 4 and 4th in the 5 cube and won the hotsaw. Jody and jay feel fee to hope in here!!!!!!!!!!!

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22572
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Jackson ,Alabama
« Reply #14 on: November 06, 2011, 12:56:57 pm »
Jody isnt here but that evil twin is  ;)  That new 3ci must be flying to get 1st down there and bet it is getting stronger + faster the more he runs it.

Good job Jay on the hotsaw win. I know it takes a good operator to make those 3 cuts cold start racing a saw that fast. WTG

Those Bertrand and Helsel hotsaws were quicker then I could think and I should have just stuck with the 166 hotsaw. By the way was the 166 down there this year?
REDNECK Saw Repair Getter Done

Offline stonecold

  • 3 cube
  • *
  • Posts: 6
  • Karma: 1
Re: Jackson ,Alabama
« Reply #15 on: November 06, 2011, 03:12:36 pm »
Thanks, that saw is a hand full, it wheelied with me on the start but got it under control just in time. after it was over and i got to thinking about it, it scared the crap out of me lol. i didnt see the 166 but i wasnt looking that much so it could have been there. Jody did real good running his 3 good job to him.

Offline Snoopy

  • 5 cube
  • ***
  • Posts: 128
  • Karma: 22
Re: Jackson ,Alabama
« Reply #16 on: November 06, 2011, 04:29:20 pm »
Yep the 166 was there ;D Bill did a good job running it.

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: Jackson ,Alabama
« Reply #17 on: November 06, 2011, 05:12:16 pm »
Good ol choppin Bill. ;D
Any video?
Yep the 166 was there ;D Bill did a good job running it.
Ron

Offline Snoopy

  • 5 cube
  • ***
  • Posts: 128
  • Karma: 22
Re: Jackson ,Alabama
« Reply #18 on: November 06, 2011, 05:19:44 pm »
I think there might be some vids coming ;)

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: Jackson ,Alabama
« Reply #19 on: November 06, 2011, 05:29:01 pm »
Cool 8)
Ron

 

Related Topics

  Subject / Started by Replies Last post
3 Replies
135 Views
Last post June 08, 2011, 10:26:25 pm
by mcbob
1 Replies
73 Views
Last post May 26, 2011, 09:25:06 pm
by rgclmc
12 Replies
977 Views
Last post June 09, 2016, 03:19:10 pm
by Cut4fun .
6 Replies
614 Views
Last post February 01, 2013, 09:23:36 am
by uconnsaw
5 Replies
139 Views
Last post January 24, 2014, 12:37:14 am
by 3000 FPS
41 Replies
1272 Views
Last post February 17, 2014, 01:18:38 pm
by Grande Dog
23 Replies
441 Views
Last post February 21, 2015, 07:34:01 pm
by dannyupsolate
11 Replies
472 Views
Last post December 22, 2015, 09:33:33 am
by Cut4fun .
5 Replies
153 Views
Last post February 15, 2017, 01:52:49 pm
by Cut4fun
6 Replies
55 Views
Last post March 24, 2019, 07:26:07 am
by Cut4fun .