« previous next »
Pages: [1]   Go Down

Author Topic: Dolmar 116si flooding  (Read 81 times)

0 Members and 0 Guests are viewing this topic.

Offline Doug41

  • 3 cube
  • *
  • Posts: 6
  • Karma: 0
Dolmar 116si flooding
« on: April 20, 2023, 10:44:09 am »
 I have Dolmar 116si that floods just sitting there. Its like the tank pressurizes and pushes gas past the carb directley into the muffler. When I try to start it gas shoots out the muffler. Rebuilt the carb but it still floods.  I have at a shop works on chainsaws and he can't figure it out.  Anybody have any suggestions?
Logged

Share on Facebook Share on Twitter

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4616
  • Karma: 216
  • OHIO REDNECK
Re: Dolmar 116si flooding
« Reply #1 on: April 22, 2023, 07:20:35 am »
The needle seat in carb or needle bad not seating.  You rebuilt carb lately?
Logged

Offline Doug41

  • 3 cube
  • *
  • Posts: 6
  • Karma: 0
Re: Dolmar 116si flooding
« Reply #2 on: April 22, 2023, 10:29:16 am »
the repair shop I took it to rebuilt the card, and it still floods.
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23511
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Dolmar 116si flooding
« Reply #3 on: April 22, 2023, 10:56:40 am »
Quote from: Doug41 on April 22, 2023, 10:29:16 am
the repair shop I took it to rebuilt the card, and it still floods.

Seat in carb could be bad. Did they pressure test carb?

Heck try a known new carb bet that will tell ya. ;)  I had to do that on a saw a few times.
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
4 Replies
1357 Views 		Last post March 31, 2012, 07:41:36 pm
by Al Smith
5 Replies
750 Views 		Last post February 13, 2013, 09:19:15 am
by bawtwblud
Husqvarna 372 flooding

Started by Cory « 1 2 ... 7 8 » Husqvarna

70 Replies
3973 Views 		Last post March 18, 2015, 10:06:24 am
by srcarr52
3 Replies
424 Views 		Last post August 29, 2013, 10:20:40 am
by Adirondackstihl
24 Replies
2285 Views 		Last post November 12, 2017, 06:56:23 pm
by Cut4fun .
3 Replies
450 Views 		Last post April 21, 2014, 09:22:19 pm
by 3000 FPS
0 Replies
126 Views 		Last post July 03, 2014, 05:52:12 pm
by bladesx
7 Replies
705 Views 		Last post September 02, 2014, 03:29:39 pm
by Nathaniel Vansickle
5 Replies
731 Views 		Last post July 14, 2016, 08:22:07 pm
by Cut4fun .
12 Replies
500 Views 		Last post October 22, 2021, 12:06:37 pm
by pmeyers