Author Topic: Dolmar 119  (Read 3258 times)

0 Members and 0 Guests are viewing this topic.

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4477
  • Karma: 275
  • Location: Carpenter, Wyoming
Dolmar 119
« on: December 12, 2012, 05:12:26 pm »
So this is my latest Dolmar that I have aquired.   I did not have any spark when I got it and finally found a donor saw with a good ignition for a resonable price.  The muffler was beat pretty bad so once again I used the one off the donor saw as with some of the antivibration buffers.  The muffler was dented pretty good with weld on the outside all around the mounting screws where it had started to crack.  So I ground all the old weld off knocked the dents out and welded it from the inside so it would not show.   I also removed the old stock outlet and put in a double pipe.   The baffle on the inside I cut away about half of it and put a spark screen around the baffle because I will use this in National Forest land and it is required.  Saw runs excellant and just thought I would show the MM.

PP 505, 475, 445.

Share on Facebook Share on Twitter


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22115
  • Karma: 550
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Dolmar 119
« Reply #1 on: December 12, 2012, 06:46:00 pm »
I know very little about the older sachs dolmar. So I had to look up to see cc size.

http://www.acresinternet.com/cscc.nsf/ed1d619968136da688256af40002b8f7/8bb8c35b049f3fd888256b62006ac19a?OpenDocument


61cc that will work.  ;D
REDNECK Saw Repair Getter Done

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4477
  • Karma: 275
  • Location: Carpenter, Wyoming
Re: Dolmar 119
« Reply #2 on: December 12, 2012, 08:32:46 pm »
 Once again not a high revving engine but lots of torque with good compression in these saws.
PP 505, 475, 445.

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4118
  • Karma: 170
  • OHIO REDNECK
Re: Dolmar 119
« Reply #3 on: December 12, 2012, 08:52:58 pm »
compared to 3400 3700 4000?

I ran that 6000i 660mag has and it was a most impressive beast in the cut.
REDNECK Saw Repair

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: Dolmar 119
« Reply #4 on: December 12, 2012, 09:02:34 pm »
I owned a 119. It was one of the strongest 60cc saw i ever owned. But it was on the heavy side.
Ron

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22115
  • Karma: 550
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Dolmar 119
« Reply #5 on: December 12, 2012, 09:03:36 pm »
I owned a 119. It was one of the strongest 60cc saw i ever owned. But it was on the heavy side.

6000i was on the heavy side too.
REDNECK Saw Repair Getter Done

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4477
  • Karma: 275
  • Location: Carpenter, Wyoming
Re: Dolmar 119
« Reply #6 on: December 12, 2012, 10:14:45 pm »
Well the 119 is all magnesium including the filter cover.   So you are right it is on the heavey side, but when I get to the point I cannot lift one of them, maybe it would be time to give it up anyways. 

I have never ran a Poulan 4000 but I have my 3700 and 395 and I believe it would outcut the 3700 and close to the 395.  It was common to find the Dolmar 119 with 170 to 190 PSI from the factory.  The Poulan saws do not run that kind of compression unless you drop the cylinders in them.  Another thing is the Dolmar is a closed port cylinder and the Poulans are open port.  A side by side test would be interesting.
PP 505, 475, 445.

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: Dolmar 119
« Reply #7 on: December 12, 2012, 11:06:28 pm »
For reference, here are some pictures of my 6000iH taken by cut4fun. The saw is 60cc completely original and is identical in looks to the 6800i. The 6000/6800 came out in 1997 and were a redesign of the 116Si and 120Si. It is a sweetheart to cut with. The green Poulan seen in one of the pictures is a 1997 3500 60cc
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4477
  • Karma: 275
  • Location: Carpenter, Wyoming
Re: Dolmar 119
« Reply #8 on: December 12, 2012, 11:20:51 pm »
    Very nice 660Magnum.  Here is a pic of my 119 for comparison.
PP 505, 475, 445.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22115
  • Karma: 550
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Dolmar 119
« Reply #9 on: December 12, 2012, 11:27:00 pm »
So how close is the 119 and the 6000i ? I only know the 6000i Jim had at my place to compare to.
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
Dolmar 112

Started by 3000 FPS « 1 2 3 4 » Dolmar Makita

31 Replies
1337 Views
Last post April 16, 2015, 10:41:34 am
by 3000 FPS
4 Replies
348 Views
Last post December 14, 2013, 08:04:13 am
by farmboy
10 Replies
569 Views
Last post November 07, 2013, 03:40:00 pm
by farmboy
1 Replies
359 Views
Last post November 12, 2013, 01:38:11 pm
by Cut4fun
28 Replies
2296 Views
Last post April 09, 2016, 02:02:55 pm
by computeruser
13 Replies
630 Views
Last post January 11, 2014, 06:09:41 pm
by Bitburger
Dolmar parts

Started by aclarke « 1 2 » Dolmar Makita

11 Replies
714 Views
Last post April 23, 2014, 11:50:04 am
by KilliansRedLeo
8 Replies
428 Views
Last post August 26, 2014, 12:14:10 am
by stihls066
8 Replies
770 Views
Last post May 24, 2014, 12:12:54 am
by dutchsawdoctor
3 Replies
226 Views
Last post April 21, 2014, 09:22:19 pm
by 3000 FPS