Author Topic: dolmar 5105  (Read 2440 times)

0 Members and 1 Guest are viewing this topic.

Offline EHP

  • Gas Hotsaw
  • ******
  • Posts: 637
  • Karma: 80
Re: dolmar 5105
« Reply #20 on: August 12, 2013, 05:47:30 pm »
it will gain power with a muffler mod , just donot go crazy on making the opening huge like on a husky , what your doing is what I see alot of so calling modders are doing and that is tighten the squish up but donot report the ports , yes tightening up the squish will gain you torque but because you lowered the transfer and ext port you will make the torque at a lower rpm in the wood , Raise your ports back up and you will gain torque and raise your in the wood rpms , On a 5100 running a 16 inch bar and 3/8's chain with you pushing some you should hold at least a 12,000 rpms in the wood , 12,400 or 12,500 is what I shoot for on a woodsport job , These saws pull pretty good and are nice and light and easy to operate , When I do vidoes I donot let the saw sit there are scream , ya it might sound good but it ain't cutting **** so how do you know what the hell the motor has for power , I know myself I would far sooner see a 10 sec cut where the motor has to work compared to a 15 second scream that really shows nothing . Like I said before yes you raise the transfers but donot go wild on them or you will have a door  stop  ;D

Offline brokenbudget

  • Nitro Hotsaw
  • *******
  • Posts: 900
  • Karma: 67
  • Location: brockville ontario canada
Re: dolmar 5105
« Reply #21 on: August 12, 2013, 06:12:55 pm »
thanks ed! loud and clear! 8)  that's the info i was looking for! :)
when I grow up, i wanna be an adult.

Offline Old Iron Logging

  • Nitro Hotsaw
  • *******
  • Posts: 1134
  • Karma: 82
Re: dolmar 5105
« Reply #22 on: August 12, 2013, 07:48:24 pm »
Listen to Ed on the 5100. Had him port one for me when they came out. Used it hard for a winter cutting 16-24 inch hardwood. Was using a 7900 before. Never used the 7900 again.

Offline EHP

  • Gas Hotsaw
  • ******
  • Posts: 637
  • Karma: 80
Re: dolmar 5105
« Reply #23 on: August 13, 2013, 04:43:43 pm »
as far as heat goes in the motor you can push the 5100/5105  pretty good before they give up , I know most hate this but always run lots of oil in your gas and from what I have been seeing for years is the crank bearing just last longer , On my stock or some what stock motors I run 40-1 and on my hotter ported motors I run 32-1 , I have a couple real hot motors and run 20-1 in them .

Dolmar to me is the most misunderstood motor out there and I'm not really sure why cause I find them 1 of the easiest to get good power out of , I can port a 7900 in less time than I think any other saw and some saws take double the time to do the engine work, The biggest mistake I have seen lots of times is guys try porting the 7900 using 372 porting numbers and that will not work at all , If you raise the transfers up to 372 porting numbers you better be running on alcohol cause it will not make enough power on gas to cut a broom handle , It will sound mean until you hit the wood , so you better just fire it up and talk about how fast it is and make sure you donot show anyone  ;D

 

Related Topics

  Subject / Started by Replies Last post
2 Replies
1732 Views
Last post December 10, 2011, 10:38:37 pm
by 660magnum
1 Replies
1459 Views
Last post June 09, 2012, 11:26:16 am
by rms61moparman
44 Replies
3351 Views
Last post February 20, 2014, 09:06:17 pm
by aclarke
29 Replies
2118 Views
Last post July 25, 2014, 11:56:00 am
by farmboy
3 Replies
298 Views
Last post March 13, 2015, 01:45:29 pm
by 660magnum
13 Replies
1025 Views
Last post August 27, 2014, 09:56:02 pm
by 660magnum
12 Replies
784 Views
Last post May 24, 2015, 08:38:38 pm
by OldJack
7 Replies
1862 Views
Last post April 08, 2016, 01:16:15 pm
by Cut4fun .
1 Replies
806 Views
Last post April 04, 2019, 06:43:25 pm
by Cut4fun .
2 Replies
369 Views
Last post April 01, 2023, 09:46:59 am
by Cut4fun