« previous next »
Pages: 1 ... 8 9 10 11 12 [13]   Go Down

Author Topic: Dolmar 6100  (Read 6098 times)

0 Members and 0 Guests are viewing this topic.

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 150
  • Location: Hayesville, NC
Re: New ps 6100
« Reply #120 on: December 04, 2017, 09:32:31 pm »
You can use Oregon std. 3/8" 7t sprocket it would probably be cheaper than Makita/Dolmar.  Mine all came with 3/8" .050 x72dl.  Did dealer swap on .325?  Check Performance Outdoor Power Equipment for hard case.  They will fit in a Husky box.
Shep
Logged
Informative Informative x 1 View List

Offline Nathaniel Vansickle

  • Piped Saw
  • *****
  • Posts: 468
  • Karma: 92
  • Location: Newcomerstown ,Ohio
Re: New ps 6100
« Reply #121 on: December 05, 2017, 08:52:53 am »
the echo tough chest will hold a 6100 with just a little modification. either cut out the inner liner where the spike hits or use a heat gun and form it around.
Logged
5105H and 6400H in stock

Performance Outdoor Equipment
performanceoutdoorequipment.com
Dolmar, Echo, Jonsered

Informative Informative x 1 View List

Offline rockfishon

  • 4 cube
  • **
  • Posts: 59
  • Karma: 8
Re: New ps 6100
« Reply #122 on: December 06, 2017, 02:41:31 pm »
Quote from: farmboy on December 04, 2017, 09:32:31 pm
You can use Oregon std. 3/8" 7t sprocket it would probably be cheaper than Makita/Dolmar.  Mine all came with 3/8" .050 x72dl.  Did dealer swap on .325?  Check Performance Outdoor Power Equipment for hard case.  They will fit in a Husky box.
Shep

My 6100 box shows factory numbering of 20 325 ST on the edge.
Logged

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 150
  • Location: Hayesville, NC
Re: New ps 6100
« Reply #123 on: December 06, 2017, 09:39:27 pm »
Dealer must have ordered it w/.325.  Suprising since 6100 pulls a 24" 3/8" just fine.  6100 fits a Husky hard box w/no modification.  6400-7900 won't fit without modding the box for spikes to fit.
Shep
Logged
Like Like x 2 View List

Offline Nathaniel Vansickle

  • Piped Saw
  • *****
  • Posts: 468
  • Karma: 92
  • Location: Newcomerstown ,Ohio
Re: New ps 6100
« Reply #124 on: December 07, 2017, 08:48:03 am »
.325 is unusual but not unheard of on them, I actually ordered 6 or so of them last month, they were the only dolmar branded 6100's available so ordered them instead of makita branded saws
Logged
5105H and 6400H in stock

Performance Outdoor Equipment
performanceoutdoorequipment.com
Dolmar, Echo, Jonsered

Useful Useful x 2 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22568
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Dolmar 6100 Makita
« Reply #125 on: February 11, 2019, 12:58:46 pm »
CRG Member brought over a dolmar makita 6100 for me to run. After doing some trading.
First stock 6100 I finally got to run. Reminds me of the echo 590 weight. Would have like to had it in last summer 60cc shoot out with his jonsered 2260 too. Like to run 590 620 6100 all back to back. Thanks.
Runs like a 60cc to me. Nice in cut with what I think was a 20" 3/8. Nice job on the chain too.

Logged
REDNECK Saw Repair Getter Done
Pages: 1 ... 8 9 10 11 12 [13]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
4 Replies
799 Views 		Last post March 24, 2012, 11:18:52 am
by farmboy
12 Replies
1247 Views 		Last post October 14, 2012, 06:43:27 am
by man of stihl
2 Replies
1071 Views 		Last post July 24, 2012, 02:02:06 pm
by Cut4fun
Dolmar 119

Started by 3000 FPS « 1 2 3 4 5 » Dolmar Makita

42 Replies
3696 Views 		Last post March 08, 2016, 11:11:25 pm
by 660magnum
1 Replies
80 Views 		Last post August 16, 2013, 07:34:45 pm
by fordfairlane78
22 Replies
991 Views 		Last post September 05, 2013, 10:23:36 pm
by KilliansRedLeo
Dolmar 112

Started by 3000 FPS « 1 2 3 4 » Dolmar Makita

31 Replies
1684 Views 		Last post April 16, 2015, 10:41:34 am
by 3000 FPS
10 Replies
668 Views 		Last post November 07, 2013, 03:40:00 pm
by farmboy
1 Replies
426 Views 		Last post November 12, 2013, 01:38:11 pm
by Cut4fun
9 Replies
248 Views 		Last post December 19, 2013, 08:36:56 pm
by fastleo151