Author Topic: Dolmar 9000  (Read 1911 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Dolmar 9000
« Reply #20 on: November 01, 2017, 11:59:14 am »
Popped muffler off. I just smiled   ;D.  Cylinder looks like new. Not hurt.  All that is on piston is detonation erosion on front lip part of top of piston. Not even all the way around.
REDNECK Saw Repair Getter Done

Offline jmester

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2048
  • Karma: 157
  • Location: MD
Re: Dolmar 9000
« Reply #21 on: November 01, 2017, 04:57:34 pm »
What causes detonation erosion anyway? Thanks for getting it.
FEAR NO TREE. FEAR GOD.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Dolmar 9000
« Reply #22 on: November 01, 2017, 06:24:24 pm »
IMO running old mix.

Also got curious and pulled recoil cover, top cover, plug etc.   Tested after regapping coil as I wanted to knw as 1 side looked tight. Reads low and then high some times.  Mostly low.

top left recoil bolt not tight but there. So put plasic gage to make hold tight for you for now.

wrong plug in it but checked psi. I was huffed at 140psi and stopped pulling. cylinder again looked great through plug hole.

Looking in tank the end of fuel line deteriorated some and missing fuel filter.

somebody in past had been running 3/8 8T

air filter I thought looked like new.

Have pics but my dsl as been crap today.

only pics I could get resized on bf cr group.

REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Dolmar 9000
« Reply #23 on: November 02, 2017, 08:42:36 am »
I seem to recall one of my stock stihl 084 had that same type of front top erosion on the piston. I ran it as it was no problems. 
@adam32 was  that the one you traded for and I had got from Adam?
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Dolmar 9000
« Reply #24 on: November 02, 2017, 09:13:13 am »
Being 52mm bore I was wondering about the piston specs.  Meteor piston 44     12 X 33 X 8    Will try and find my 52mm piston thread to compare.
REDNECK Saw Repair Getter Done

Offline Nathaniel Vansickle

  • Piped Saw
  • *****
  • Posts: 468
  • Karma: 92
  • Location: Newcomerstown ,Ohio
Re: Dolmar 9000
« Reply #25 on: November 02, 2017, 12:37:07 pm »
bar studs modified to accept a stihl mount bar or what? looks like flats have been cut into them and pretty sure they are supposed to be round.


5105H and 6400H in stock

Performance Outdoor Equipment
performanceoutdoorequipment.com
Dolmar, Echo, Jonsered

Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Dolmar 9000
« Reply #26 on: November 02, 2017, 12:53:08 pm »
bar studs modified to accept a stihl mount bar or what? looks like flats have been cut into them and pretty sure they are supposed to be round.




I put a d009 on it fit perfect but didnt look close. Will take a closer look now though. To see if there was space at bottom.   Have a stihl mount here too to check.
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Dolmar 9000
« Reply #27 on: November 02, 2017, 01:02:54 pm »
Dont know the saws to know what is what but D009 fits and D025 or whatever the stihl mount is 040 041 bar dont.

Loading pics
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Dolmar 9000
« Reply #28 on: November 02, 2017, 01:08:36 pm »
both pics d009 top  stihl bottom



REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Dolmar 9000
« Reply #29 on: November 02, 2017, 01:18:36 pm »
Going by this new stud pic sure appears someone had flat filed the ones on it though.

So mount was the 9000 9010 suppose to be?  Big stihl 14mm or stihl 12mm or what?  That one link shows d009 but they have been wrong before.



REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
4 Replies
714 Views
Last post March 24, 2012, 11:18:52 am
by farmboy
12 Replies
1056 Views
Last post October 14, 2012, 06:43:27 am
by man of stihl
2 Replies
1010 Views
Last post July 24, 2012, 02:02:06 pm
by Cut4fun
Dolmar 112

Started by 3000 FPS « 1 2 3 4 » Dolmar Makita

31 Replies
1323 Views
Last post April 16, 2015, 10:41:34 am
by 3000 FPS
3 Replies
438 Views
Last post June 19, 2014, 04:40:38 pm
by dutchsawdoctor
1 Replies
141 Views
Last post September 10, 2014, 01:29:01 pm
by aclarke
20 Replies
412 Views
Last post October 24, 2014, 06:41:20 pm
by Windy_Acres
3 Replies
175 Views
Last post January 13, 2015, 12:03:22 am
by dannyupsolate
8 Replies
506 Views
Last post April 12, 2016, 06:56:28 pm
by Cut4fun .
1 Replies
577 Views
Last post February 16, 2019, 09:11:02 am
by Cut4fun .