Author Topic: Dolmar Makita 5100 5105 510 5000  (Read 80 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4616
  • Karma: 216
  • OHIO REDNECK
Dolmar Makita 5100 5105 510 5000
« on: April 01, 2023, 09:46:01 am »
Just had another class to refresh on chainsaw repair group FB on this chassis. So saving.

Dolmar Makita 5100 5105 510 5000. Havent messed with these in years. Need refresher. 
Some PHO dry weight of the 50cc.
510 was the open port with aluminum case.
5100 closed port with mag case.
5105 CAT muffler mag case.
5000? 

Share on Facebook Share on Twitter

Informative Informative x 1 View List

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4616
  • Karma: 216
  • OHIO REDNECK
Re: Dolmar Makita 5100 5105 510 5000
« Reply #1 on: April 01, 2023, 09:46:27 am »
Kevin LaVanway Sr
5100S had a higher limited coil with a windowed piston. 5105 uses a slab sided piston with a cat muffler and a lower limiter. Same saw otherwise.

Kevin LaVanway Sr
Kevin Smith
Itís possible port timing is less jazzy in the 05. Canít remember for certain. The carb is too small for huge rpm gains so I port them with an emphasis on torque. All of them that I have seen come into my shop had 3/8 on them as they should have.

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4616
  • Karma: 216
  • OHIO REDNECK
Re: Dolmar Makita 5100 5105 510 5000
« Reply #2 on: April 01, 2023, 09:46:59 am »
Nathaniel VansickleGroup expert
510/5105 were available with 16, 18, 20" bars in both 325 and 3/8. Dam near the same price no matter how they were spec. So most shops ordered them with 20" 3/8 and most shops that had a clue avoided the 3/8 18" bar because of the oddball DL count

Nathaniel VansickleGroup expert
510, 5121= same saw. 5100, 5105, 5000= same saw. 5001, 5105H= same saw as 5105 but with heated handle

    Reply
    12m

Nathaniel VansickleGroup expert
510/5121 were aluminum cased except the last of production run was mag cased... not a clue if that was the last 3 month or year or 2 years of production...I just know they did away with the aluminum case at the end.

    Reply
    10m

Nathaniel VansickleGroup expert
510 was built in Germany then switched to China assembly then back to Germany

 

Related Topics

  Subject / Started by Replies Last post
2 Replies
1431 Views
Last post December 10, 2011, 10:38:37 pm
by 660magnum
1 Replies
1201 Views
Last post June 09, 2012, 11:26:16 am
by rms61moparman
8 Replies
1023 Views
Last post September 18, 2012, 03:51:15 pm
by Cut4fun .
23 Replies
1840 Views
Last post August 13, 2013, 04:43:43 pm
by EHP
44 Replies
2487 Views
Last post February 20, 2014, 09:06:17 pm
by aclarke
3 Replies
152 Views
Last post March 13, 2015, 01:45:29 pm
by 660magnum
3 Replies
155 Views
Last post October 08, 2014, 07:59:42 am
by farmboy
8 Replies
432 Views
Last post December 19, 2014, 06:11:10 am
by Chainsawr
12 Replies
440 Views
Last post May 24, 2015, 08:38:38 pm
by OldJack
7 Replies
1366 Views
Last post April 08, 2016, 01:16:15 pm
by Cut4fun .