Author Topic: Maktia Dolmar 8100  (Read 693 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22019
  • Karma: 542
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Maktia Dolmar 8100
« on: July 27, 2016, 06:04:57 pm »
After letting it go for almost 3 weeks now and still only rumors.

Makita Dolmar 8100 80.7cc 52mm bore 38mm stroke is my bet.  I would also bet it will be influenced from the ek8100

Makita EK8100 p+c below





REDNECK Saw Repair Getter Done

Share on Facebook Share on Twitter


Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Maktia Dolmar 8100
« Reply #1 on: July 28, 2016, 04:35:15 am »
Could be interesting.  Doubt I'll replace my 181SE with one, but I'm still looking forward to seeing this if it materializes.  Replacement for the 7910 I take it?  My friend Dave's 6910 with the 7910 top end is a strong runner.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Nathaniel Vansickle

  • Piped Saw
  • *****
  • Posts: 468
  • Karma: 92
  • Location: Newcomerstown ,Ohio
Re: Maktia Dolmar 8100
« Reply #2 on: July 28, 2016, 04:26:43 pm »
only one small problem with basing a new saw off the 8100 cutoff saw......it already exists and is called a 7910
5105H and 6400H in stock

Performance Outdoor Equipment
performanceoutdoorequipment.com
Dolmar, Echo, Jonsered

Useful Useful x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22019
  • Karma: 542
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Maktia Dolmar 8100
« Reply #3 on: July 28, 2016, 06:55:09 pm »
only one small problem with basing a new saw off the 8100 cutoff saw......it already exists and is called a 7910

ek8100 is listed as 81cc  ? so guessing it was 80.7cc so it has a 38mm stroke instead of the 7910 37mm stroke ?

7910 was 79cc

feed the need to WAG ;)
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22019
  • Karma: 542
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Maktia Dolmar 8100
« Reply #4 on: July 28, 2016, 07:11:26 pm »
Same crank shown in 8100 comes back to the dolmar 8216

Model:
   
PC-8216
Engine manufacturer
   
DOLMAR
Engine
   
2-stroke
Displacement
   
81 cc (5 cu. in)

Fun guessing anyways.  :P
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22019
  • Karma: 542
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Maktia Dolmar 8100
« Reply #5 on: July 28, 2016, 07:45:13 pm »
Found one called 8240 too. But all the time I have for goofing off guessing. 

REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22019
  • Karma: 542
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Maktia Dolmar 8100
« Reply #6 on: July 28, 2016, 08:30:51 pm »
Nate how about a big 6100 style ;) in 52mm 38mm 8100  ;D :P
REDNECK Saw Repair Getter Done

Offline Nathaniel Vansickle

  • Piped Saw
  • *****
  • Posts: 468
  • Karma: 92
  • Location: Newcomerstown ,Ohio
Re: Maktia Dolmar 8100
« Reply #7 on: July 29, 2016, 10:23:59 am »
i havent heard much about the new 80+cc saw except that it will be similar in design to the 6100 and be based on west coast cutting conditions so i expect a functional and comfortable full wrap handle and large dual bucking spikes. I have been lobbying for 90+cc every chance i get but everytime they shoot me down on that and say its not happening, expect low to mid 80cc.
5105H and 6400H in stock

Performance Outdoor Equipment
performanceoutdoorequipment.com
Dolmar, Echo, Jonsered

Informative Informative x 1 View List

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Maktia Dolmar 8100
« Reply #8 on: July 29, 2016, 01:31:39 pm »
A west coast 5-5.5ci saw with a good full wrap is interesting indeed.  Now if we had some dealers out here to sell and service them then that'd be great...
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline mdavlee .

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1968
  • Karma: 171
Re: Maktia Dolmar 8100
« Reply #9 on: July 29, 2016, 05:11:50 pm »
Will we see it before husky releases the 572 or whatever is what I wonder.

 

Related Topics

  Subject / Started by Replies Last post
4 Replies
714 Views
Last post March 24, 2012, 11:18:52 am
by farmboy
12 Replies
1056 Views
Last post October 14, 2012, 06:43:27 am
by man of stihl
2 Replies
1010 Views
Last post July 24, 2012, 02:02:06 pm
by Cut4fun
6 Replies
1307 Views
Last post October 25, 2015, 09:31:29 pm
by mikehonda
22 Replies
877 Views
Last post September 05, 2013, 10:23:36 pm
by KilliansRedLeo
Dolmar 112

Started by 3000 FPS « 1 2 3 4 » Dolmar Makita

31 Replies
1325 Views
Last post April 16, 2015, 10:41:34 am
by 3000 FPS
3 Replies
438 Views
Last post June 19, 2014, 04:40:38 pm
by dutchsawdoctor
1 Replies
141 Views
Last post September 10, 2014, 01:29:01 pm
by aclarke
3 Replies
175 Views
Last post January 13, 2015, 12:03:22 am
by dannyupsolate
8 Replies
506 Views
Last post April 12, 2016, 06:56:28 pm
by Cut4fun .