Author Topic: Picked of a used Dolmar 5100s  (Read 2550 times)

0 Members and 6 Guests are viewing this topic.

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 150
  • Location: Hayesville, NC

  • Total Badges: 31
    Badges: (View All)
    Level 6 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary 1000 Posts Old Browser
Re: Picked of a used Dolmar 5100s
« Reply #10 on: March 04, 2012, 10:10:07 am »
Most of the time you can clean the alum. transfer off of the cyl. with a Qtip and muratic acid.  Heat the cyl. (works better when hot) apply acid on transfer repeat til gone.  You can use scotchbrite pad or 400 grit wet-n-dry sandpaper.  Google the PN for the piston to find best price.  The new piston doesn't have windows it has been replaced with a lighter non windowed piston.  The last one I got was from the link below.  Hope this helps with your project.   
http://www.psep2.biz/pages/OemParts?aribrand=DOL#/Dolmar/PS-5100_S_Chain_Saws_-_Gasoline/Cylinder%2c_crankcase/2S01070065/2S01070003C
Shep

Offline DB_43725

  • 3 cube
  • *
  • Posts: 17
  • Karma: 1

  • Total Badges: 12
    Badges: (View All)
    Level 3 Second year Anniversary Search Karma Level 2 Avatar
Re: Picked of a used Dolmar 5100s
« Reply #11 on: March 04, 2012, 08:50:42 pm »
Well I had already got the p@c before i recieved the saw,,, So im just gona change the hole anchalota,,, but what concerns me is in the lower end down in the crankcase,,, now I checked and the main bearing have no play side to side and no up and down ,, but the crank has rubed the paint off of the case didnt seem to get any metal, but the throws on the crank did take the paint off on the starter side, well the paint musta went up the transferrs because its not their anywhere, could this be what cause the piston to seize. It is streeked about a half in wide from top to bottom, sticking the ring in the grove.

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO

  • Total Badges: 39
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary 5000 Posts Third year Anniversary
Re: Picked of a used Dolmar 5100s
« Reply #12 on: March 04, 2012, 09:04:09 pm »
The bearing and seal are probably bad on that side?
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline DB_43725

  • 3 cube
  • *
  • Posts: 17
  • Karma: 1

  • Total Badges: 12
    Badges: (View All)
    Level 3 Second year Anniversary Search Karma Level 2 Avatar
Re: Picked of a used Dolmar 5100s
« Reply #13 on: March 04, 2012, 09:37:46 pm »
Well im not so sure,,reason being on that half ,,inside of the counter weight the paint apears to be bubbling up,, so if I had to guess thats what made the counter weight rub it off of the crank case.

Offline wkpoor

  • 4 cube
  • **
  • Posts: 61
  • Karma: 2

  • Total Badges: 12
    Badges: (View All)
    Third year Anniversary Level 3 Karma Second year Anniversary Combination Topic Starter
Re: Picked of a used Dolmar 5100s
« Reply #14 on: May 06, 2012, 09:52:34 am »
Since coming across a spun bearing for myself I would always check it first. Simply remove clutch and turn flywheel by hand. It will evident if it is free in the case. End play is normal but radial play is not.

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 150
  • Location: Hayesville, NC

  • Total Badges: 31
    Badges: (View All)
    Level 6 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary 1000 Posts Old Browser
Re: Picked of a used Dolmar 5100s
« Reply #15 on: May 19, 2012, 08:33:39 am »
How is the 5100 project coming?  I'd be interested in the old cyl. PM me if you want to get rid of it.
Shep

Offline DB_43725

  • 3 cube
  • *
  • Posts: 17
  • Karma: 1

  • Total Badges: 12
    Badges: (View All)
    Level 3 Second year Anniversary Search Karma Level 2 Avatar
Re: Picked of a used Dolmar 5100s
« Reply #16 on: June 04, 2012, 12:25:13 am »
Sorry havent been on here for a wile,,, But I got 4 ,,5100s now been practicing taking them apart and reasembling them,,LOL,,, Fig. was a good time to learn how to port a saw. I did learn real quick big is not always better. But Im getting better at it as each one gets faster,,cut speed,,, Maybe I will get one to suit me one of these days. But to answer your question,no I dont have any cylinders that are any good now,except the ones im using.

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 150
  • Location: Hayesville, NC

  • Total Badges: 31
    Badges: (View All)
    Level 6 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary 1000 Posts Old Browser
Re: Picked of a used Dolmar 5100s
« Reply #17 on: June 07, 2012, 07:26:43 am »
Just finished up a WP 5100 last week.  Haven't started it yet.  My other 3 are new.  Next is a 510 with a 5100 cyl.  Always looking for 5100 cyl's.  I did drill and tap the WP cyl. for a decomp. came out nice.  Just happened my drill press is dead level.  Cut a plate out of 1/4" plexiglass to mount cyl on.  Then used a laser level to check for vertical.  Drilled a 3/32" into cyl.  Had to go slow the plexiglass wanted to flex some.  Then 4 larger bit sizes to 11/32" 15mm deep.  Another note I did square up the casting for decomp with a file.
Shep

 

Related Topics

  Subject / Started by Replies Last post
2 Replies
735 Views
Last post December 23, 2014, 08:48:28 am
by Cut4fun .
4 Replies
531 Views
Last post May 08, 2011, 07:20:52 am
by peppone
2 Replies
1592 Views
Last post December 10, 2011, 10:38:37 pm
by 660magnum
13 Replies
1483 Views
Last post February 25, 2012, 10:21:18 pm
by Cut4fun .
5100S Problem

Started by wkpoor « 1 2 » Dolmar Makita

18 Replies
2072 Views
Last post May 03, 2012, 11:57:26 pm
by wkpoor
picked two more CS-440

Started by leec « 1 2 3 » Echo

24 Replies
1845 Views
Last post September 08, 2015, 04:46:03 pm
by leec
3 Replies
472 Views
Last post September 10, 2014, 09:13:00 pm
by pigpen60
5100s air leak

Started by dolmar « 1 2 3 » Dolmar Makita

21 Replies
1379 Views
Last post January 16, 2015, 04:12:20 am
by dolmarfan
0 Replies
257 Views
Last post March 07, 2017, 03:14:18 pm
by AmericanPsycho
1 Replies
353 Views
Last post March 26, 2019, 02:25:51 pm
by Efisher26