« previous next »
Pages: [1]   Go Down

Author Topic: replace flywheel on Makita DCS6421  (Read 396 times)

0 Members and 0 Guests are viewing this topic.

Offline labdon

  • pruner
  • *
  • Posts: 1
  • Karma: 0
replace flywheel on Makita DCS6421
« on: July 17, 2016, 05:58:51 pm »
I removed the flywheel so I could replace the coil. I installed the new flywheel. However the flywheel came loose and sheared off the key cast into the flywheel. I installed a second flywheel and used Loctite 242. This second flywheel also came loose and sheared the key. Any suggestions on how to keep this flywheel in place? Thanks
Logged

Share on Facebook Share on Twitter

Disagree Disagree x 1 View List

Offline jmester

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2046
  • Karma: 156
  • Location: MD
Re: replace flywheel on Makita DCS6421
« Reply #1 on: July 17, 2016, 09:04:44 pm »
It should be a taper fit. I use a rubber mallet to help seat the flywheel. Make sure you support the crankshaft on the pto to help prevent any side to side movement. Make sure that you torque the nut. Not sure what dolmar has for the torque spec but most stihls that size are around 25 ft lbs or 33nm. Hope this helps you as flywheels are expensive.
Logged
FEAR NO TREE. FEAR GOD.

Offline Nathaniel Vansickle

  • Piped Saw
  • *****
  • Posts: 468
  • Karma: 92
  • Location: Newcomerstown ,Ohio
Re: replace flywheel on Makita DCS6421
« Reply #2 on: July 17, 2016, 09:26:05 pm »
be sure your mounting surfaces are clean and free of any oil. they are taper fit and its that taper that locks the flywheel in place more than the nut
Logged
5105H and 6400H in stock

Performance Outdoor Equipment
performanceoutdoorequipment.com
Dolmar, Echo, Jonsered

Like Like x 1 View List
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
Makita 540 ?

Started by Al Smith « 1 2 3 4 » Dolmar Makita

32 Replies
1344 Views 		Last post October 05, 2012, 07:37:14 am
by pete
2 Replies
651 Views 		Last post November 06, 2013, 07:57:16 pm
by 3000 FPS
8 Replies
375 Views 		Last post March 12, 2014, 09:42:07 am
by KilliansRedLeo
20 Replies
1112 Views 		Last post July 25, 2014, 07:54:45 pm
by fuzz1500
makita 6401

Started by pigpen60 « 1 2 » Dolmar Makita

16 Replies
468 Views 		Last post November 01, 2014, 02:57:00 am
by pete
makita 6421

Started by pigpen60 « 1 2 » Dolmar Makita

15 Replies
409 Views 		Last post September 11, 2014, 08:47:10 pm
by pigpen60
10 Replies
341 Views 		Last post April 16, 2015, 08:12:11 pm
by SawTroll
1 Replies
276 Views 		Last post March 06, 2016, 05:57:13 pm
by Cut4fun .
4 Replies
149 Views 		Last post February 27, 2017, 05:53:53 am
by dmccann
3 Replies
144 Views 		Last post February 08, 2018, 08:50:19 pm
by mdavlee .