Author Topic: Sachs Dolmar 309 fits  (Read 567 times)

0 Members and 2 Guests are viewing this topic.

Offline stretch5881

  • pruner
  • *
  • Posts: 4
  • Karma: 0
Sachs Dolmar 309 fits
« on: February 11, 2017, 05:33:18 pm »
Hi all,
 I'm working on a Sachs 309 concrete saw. It was brought to me because he couldn't start it. Badly scored p&c (60 psi).
 So, new cylinder kit installed. Starts and idles but won't rev. Tore carb down and ultrasonic cleaned and new kit. New fuel line and filter. No change. Pressure test carb inlet, pops at 12#. Pressure tested the crankcase and no seal or gasket leakage. Tank vent is working as it should. I have tore the carburetor apart at least 6 times in case I missed something (not my first carb rebuild).
 The saw starts and idles as it should, but when you blip the throttle, it will almost die, then return to idle. If I bring the rpm up slowly, it will get up to half speed and die like it ran out of fuel. Also tried 3 new spark plugs. Spark tester shows spark until dead.
 I have run out of ideas.

Share on Facebook Share on Twitter


Offline pete

  • Piped Saw
  • *****
  • Posts: 499
  • Karma: 37
Re: Sachs Dolmar 309 fits
« Reply #1 on: February 11, 2017, 11:37:40 pm »
is the exhaust clear no blocked muffler screen

Online 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4547
  • Karma: 292
  • Location: Carpenter, Wyoming
Re: Sachs Dolmar 309 fits
« Reply #2 on: February 12, 2017, 12:20:25 am »
I think you still have a air leak somewhere.  If not the crank seals then start looking at other places like the carb intake.   Or maybe it could be the impulse is blocked or partially blocked.   But sounds more like an air to me.
Also remember the coils on those are rev limited because the blades are not make for high rpm's.
PP 505, 475, 445.

Offline stretch5881

  • pruner
  • *
  • Posts: 4
  • Karma: 0
Re: Sachs Dolmar 309 fits
« Reply #3 on: February 12, 2017, 09:33:36 am »
 Crankcase pressure tested ok. I used soapy water to test seals, intake and base gaskets. No screen in muffler and muffler is clear.
I think I have a parts saw in the shed. I'll have to see if the coil is the same and try that.

 

Related Topics

  Subject / Started by Replies Last post
Sachs Dolmar 166

Started by Cut4fun « 1 2 ... 5 6 » Dolmar Makita

53 Replies
5042 Views
Last post June 18, 2021, 02:07:38 pm
by Bitburger
7 Replies
1535 Views
Last post January 02, 2012, 07:10:50 pm
by rms61moparman
21 Replies
2224 Views
Last post May 31, 2014, 10:52:19 am
by man of stihl
0 Replies
51 Views
Last post April 12, 2014, 12:28:35 am
by stihls066
48 Replies
3712 Views
Last post February 12, 2020, 08:56:51 pm
by Cut4fun .
18 Replies
972 Views
Last post February 14, 2015, 08:40:38 am
by man of stihl
0 Replies
72 Views
Last post August 10, 2015, 02:17:30 pm
by stihls066
3 Replies
71 Views
Last post November 03, 2017, 11:53:58 pm
by ray benson
0 Replies
233 Views
Last post July 11, 2020, 09:27:57 am
by Cut4fun .
6 Replies
82 Views
Last post June 25, 2021, 08:46:36 am
by Yozhek