Author Topic: Echo 8000  (Read 3749 times)

0 Members and 0 Guests are viewing this topic.

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2111
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Echo 8000
« Reply #60 on: March 18, 2015, 05:07:05 pm »
I run JGX on my 32" + bars on 5ci class saws.  I have a loop of that Carlton skip chisel (105DL) but haven't ran it yet.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21166
  • Karma: 474
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Echo 8000
« Reply #61 on: April 10, 2015, 07:02:35 pm »
I am even more impressed with this 800V 8000 today. I forgot back in 2011 or so I had put a 8T and short bar for gtg fun play in 10x10 cants. 
I have been running 24" 8T buried since then and at the 2013 GTG etc when it was out cutting 5200 P61 etc.

I had wondered why the 36" 116DL was tight. So I counted to see above. 7T on there now.







REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2111
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Echo 8000
« Reply #62 on: April 10, 2015, 09:23:00 pm »
Nice.  Now get 'em in some wood. 8)
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 3922
  • Karma: 143
  • OHIO REDNECK
Re: John Deere 800V Echo 8000
« Reply #63 on: August 09, 2015, 12:03:46 pm »
New owner of the john deere 800v sent me 3 pics and text yesterday.  Wish I knew how to transfer pics, but I am stupid like that.  :'(

(( It's a ripper  ;D   Pulled the 28" through dead ash like it was nothing. ))
REDNECK Saw Repair

Offline WLZecho8000P

  • pruner
  • *
  • Posts: 1
  • Karma: 1
  • Location: TN
Re: Echo 8000
« Reply #64 on: September 15, 2017, 12:39:50 pm »
Wouldn't trade mine for any new saw.  Hard on the back, but she will run first pull longer than I want to run her ;D
Like Like x 1 View List

 

Related Topics

  Subject / Started by Replies Last post
13 Replies
1712 Views
Last post December 07, 2011, 05:32:23 pm
by brokenbudget
2 Replies
439 Views
Last post December 12, 2011, 06:47:38 pm
by Cut4fun .
9 Replies
1028 Views
Last post September 02, 2013, 06:30:22 pm
by Cut4fun .
3 Replies
496 Views
Last post September 15, 2013, 10:56:36 pm
by sharkey
5 Replies
654 Views
Last post March 10, 2014, 09:48:26 pm
by 3000 FPS
Echo CS-8000

Started by KilliansRedLeo « 1 2 » Echo

10 Replies
501 Views
Last post March 15, 2014, 02:03:04 pm
by Cut4fun .
11 Replies
514 Views
Last post August 13, 2015, 12:39:22 pm
by HolmenTree
5 Replies
530 Views
Last post December 24, 2015, 11:45:00 am
by Cut4fun .
1 Replies
254 Views
Last post December 23, 2015, 09:16:24 pm
by Cut4fun .
0 Replies
181 Views
Last post June 15, 2016, 08:20:51 pm
by Cut4fun .