Author Topic: CS-400 Muffler Mod  (Read 7456 times)

0 Members and 27 Guests are viewing this topic.

Offline Majorpayne

  • 3 cube
  • *
  • Posts: 19
  • Karma: 2
  • Location: Southern Illinois

  • Total Badges: 16
    Badges: (View All)
    Level 4 Fourth year Anniversary Karma Third year Anniversary Level 3 10 Posts
Re: CS-400 Muffler Mod
« Reply #40 on: January 06, 2014, 05:23:04 pm »
I tune by ear and then check it with the tach.

Offline huichex

  • 3 cube
  • *
  • Posts: 23
  • Karma: 0

  • Total Badges: 11
    Badges: (View All)
    Level 3 10 Posts Combination Topic Starter Level 2 First Post
Re: CS-400 Muffler Mod
« Reply #41 on: January 06, 2014, 06:40:33 pm »
Where can I find the max or desired rpm for the cs400?

Offline Majorpayne

  • 3 cube
  • *
  • Posts: 19
  • Karma: 2
  • Location: Southern Illinois

  • Total Badges: 16
    Badges: (View All)
    Level 4 Fourth year Anniversary Karma Third year Anniversary Level 3 10 Posts
Re: CS-400 Muffler Mod
« Reply #42 on: January 06, 2014, 06:47:32 pm »
Wide open throttle speed
(W.O.T.)
12,650 RPM
This is what it says in owners manual under technical data.

Offline sharkey

  • Piped Saw
  • *****
  • Posts: 368
  • Karma: 37

  • Total Badges: 26
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Level 5
Re: CS-400 Muffler Mod
« Reply #43 on: January 07, 2014, 01:52:03 am »
Here are the updated specs for the Echo cs-400;
http://www.echo-usa.com/tomwin41/Techdata/cs-400.pdf

No wonder that is a little hot rod, check out the ignition advance, 34 degrees at 10k rpm...

Offline Philbert

  • Gas Hotsaw
  • ******
  • Posts: 563
  • Karma: 76

  • Total Badges: 23
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Level 5 Fifth year Anniversary 500 Posts Fourth year Anniversary
Re: CS-400 Muffler Mod
« Reply #44 on: January 07, 2014, 09:19:25 am »
Thanks Sharkey. That is very helpful to have.

Is the full service manual available?

Thanks.

Philbert

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 150
  • Location: Hayesville, NC

  • Total Badges: 31
    Badges: (View All)
    Level 6 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary 1000 Posts Old Browser
Re: CS-400 Muffler Mod
« Reply #45 on: January 07, 2014, 09:36:11 pm »
Question had allready been answered I didn't read far enough.
Shep

Offline huichex

  • 3 cube
  • *
  • Posts: 23
  • Karma: 0

  • Total Badges: 11
    Badges: (View All)
    Level 3 10 Posts Combination Topic Starter Level 2 First Post
Re: CS-400 Muffler Mod
« Reply #46 on: January 10, 2014, 07:16:36 pm »
OK, so the tach is on the way!
"
These my be dumb Qs, but the max rpm is that unloaded, like not cutting... and is there a diff. between 18" and 16" bar? the book specifies 16" but mine is 18"

Offline Majorpayne

  • 3 cube
  • *
  • Posts: 19
  • Karma: 2
  • Location: Southern Illinois

  • Total Badges: 16
    Badges: (View All)
    Level 4 Fourth year Anniversary Karma Third year Anniversary Level 3 10 Posts
Re: CS-400 Muffler Mod
« Reply #47 on: January 10, 2014, 07:27:51 pm »
It is unloaded. The size bar doesn't matter.

Offline huichex

  • 3 cube
  • *
  • Posts: 23
  • Karma: 0

  • Total Badges: 11
    Badges: (View All)
    Level 3 10 Posts Combination Topic Starter Level 2 First Post
Re: CS-400 Muffler Mod
« Reply #48 on: January 11, 2014, 10:58:50 am »
Thank you!

So is there a benefit to getting an aftermarket bar?

 I got a new chain, Oregon, without the drag links. I am working on a little race with some coworkers, but weather has been real bad here lately, cold and wet. No one wants to be outside in weather like that, so I am getting the saw as ready as possible. Both of my buddys got factory Husqvarna saws.

Offline huichex

  • 3 cube
  • *
  • Posts: 23
  • Karma: 0

  • Total Badges: 11
    Badges: (View All)
    Level 3 10 Posts Combination Topic Starter Level 2 First Post
Re: CS-400 Muffler Mod
« Reply #49 on: January 19, 2014, 01:15:42 pm »
Ok, so I pulled the tach out of the package and when I placed it next to the plug wire...18888 was displayed while the saw was at idle. It is set for one spark per rev and I am going to source a new batt. Is there anything else I should check?
Thanks again
Luis

 

Related Topics

  Subject / Started by Replies Last post
4 Replies
980 Views
Last post June 18, 2012, 10:26:24 pm
by Stihlboy
Muffler

Started by jmester Stihl

3 Replies
631 Views
Last post January 15, 2013, 08:05:01 pm
by jmester
7 Replies
795 Views
Last post January 24, 2013, 04:51:40 am
by brokenbudget
372 muffler

Started by DCC « 1 2 » Husqvarna

16 Replies
1188 Views
Last post November 01, 2013, 09:06:03 pm
by mdavlee .
9 Replies
4490 Views
Last post October 23, 2013, 09:18:26 pm
by Cut4fun .
2 Replies
485 Views
Last post December 15, 2013, 04:58:39 pm
by Eccentric
7 Replies
488 Views
Last post January 19, 2014, 09:10:11 am
by The Ripper
2 Replies
645 Views
Last post February 02, 2014, 05:21:12 pm
by DickT
7 Replies
1038 Views
Last post March 02, 2014, 11:21:33 pm
by Bobby Charles
6 Replies
451 Views
Last post March 13, 2014, 09:49:45 am
by KilliansRedLeo