« previous next »
Pages: [1]   Go Down

Author Topic: CS 500 EVL Oil Pump  (Read 605 times)

0 Members and 1 Guest are viewing this topic.

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 150
  • Location: Hayesville, NC
CS 500 EVL Oil Pump
« on: July 23, 2014, 12:44:47 pm »
Know next to nothing about Echo saws only worked on 1 and that was another 500EVL.  Oil pump isn't oiling.  IPL was helpfull showed me where and how it worked.  However, I don't see anything wrong with the pump.  Orings look good on pump.  Swapped op with one out of the other 500 still not oiling?  I did notice the plunger was longer on the one out of the other saw.  Anything I should look for on these?  Is there an installed turn on the op like bottom and turn out 1 turn for initial seting?  Fairly low hr. saw.
Shep
Logged

Share on Facebook Share on Twitter

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23510
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: CS 500 EVL Oil Pump
« Reply #1 on: July 23, 2014, 05:16:01 pm »
Man I was hoping Aaron knew something.  I got nothing on these older echos either.
Logged

Offline leec

  • 6 cube
  • ****
  • Posts: 264
  • Karma: 14
  • Location: Huntsville, Ontario
Re: CS 500 EVL Oil Pump
« Reply #2 on: July 25, 2014, 11:55:09 am »
I would make sure the oil pick up filter is clear, not blocked.  I had a 351 that that needed three new o rings on the pump to works

Lee
Logged

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2117
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northwestern Wyoming
Re: CS 500 EVL Oil Pump
« Reply #3 on: November 18, 2014, 09:54:51 pm »
Just now saw this thread.  Haven't been in the Echo section much in a while.

I haven't had the oiler apart on one of these yet.  Usual things to check are the strainer and the pickup tube.  If the strainer is plugged and/or the pickup tube has gone soft, it'll stop pumping oil.  A soft tube can collapse like a tapeworm.  Page #9 of the operators manual covers oiler adjustment.  Also make sure the oil holes in the bar and bar pad are clear.

http://www.echo-usa.com/getattachment/0db00d96-3c1d-4d41-b2dc-a9cf79088994/CS500VLE_020180.pdf

http://www.echo-usa.com/Support-Help/Technical-Documents.aspx?s=cs500vl&c=en-us
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
394 oil pump ?

Started by alsled « 1 2 » Husqvarna

15 Replies
764 Views 		Last post November 23, 2013, 07:43:04 pm
by alsled
3 Replies
338 Views 		Last post August 07, 2014, 02:03:50 pm
by Cut4fun .
4 Replies
254 Views 		Last post November 22, 2014, 12:00:58 am
by 660magnum
1 Replies
450 Views 		Last post January 11, 2016, 10:17:47 pm
by jmester
7 Replies
536 Views 		Last post January 31, 2016, 03:15:43 pm
by 3000 FPS
28 Replies
1230 Views 		Last post July 19, 2017, 07:45:14 am
by Nixon
18 Replies
738 Views 		Last post December 20, 2017, 04:20:19 pm
by Cut4fun .
2 Replies
357 Views 		Last post January 27, 2018, 11:37:07 pm
by farmboy
3 Replies
350 Views 		Last post June 04, 2019, 08:36:12 am
by ray benson
0 Replies
242 Views 		Last post July 20, 2022, 09:42:16 am
by Cut4fun .