« previous next »
Pages: 1 [2] 3 4   Go Down

Author Topic: Echo bar adapters 12mm to 8mm D176  (Read 1357 times)

0 Members and 0 Guests are viewing this topic.

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2111
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Echo bar adapters 12mm to 8mm D176
« Reply #10 on: August 10, 2015, 01:24:18 am »
Quote from: Nathaniel Vansickle on August 07, 2015, 11:49:05 am
Echo adapters dont fit the 590/600/620. outside of studs on the 620 is 1.885 and the adapters have a spacing of 1.725. So now the question is what all will these Echo adapters fit?


AS 002 by nathaniel vansickle, on Flickr

AS 001 by nathaniel vansickle, on Flickr
Quote from: Eccentric on August 08, 2015, 12:59:08 am
I bet those are patterned off older D176 mount saws.  I will measure my Poulan, Echo, Homelite, and Lombard D176 mount saws this weekend.  Kevin if I don't post up here by Sunday evening please give me a ring or a text.  My memory isn't the best....

I measured various D176 mount saws today.  Early XL-12.  Homelite XL-800/850.  Poulan 3400.  Poulan 5200.  Lombard Cyclone.  Echo CS500VL.  Pioneer 11-60.  They all come up as being around 1.556" outside edge to outside edge.  They all fit these "S" stud spacer clips that were once common for adapting a D096/D196/UXL bar onto an A176/D176 mount saw.   That's narrower enough than the adaptors that you've received that I am not sure if they'd fit any D176 saw that I know of.  Too wide for the older saws, and too narrow for the current Echos.  Hmmm.....




'S' Spacer as used on all older A176/D176 mount saws that I am aware of.



Same 'S' spacer on the studs of an Echo CS500VL.



'S' spacer on the studs of a Lombard Cyclone.



'S' clip on a Pioneer 11-60.



'S clip on a Craftsman 5.2/Poulan 5200 CounterVibe.
Logged
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Nathaniel Vansickle

  • Piped Saw
  • *****
  • Posts: 468
  • Karma: 92
  • Location: Newcomerstown ,Ohio
Re: Echo bar adapters 12mm to 8mm D176
« Reply #11 on: August 10, 2015, 09:14:51 am »
i used to have a dozen of those "S" adapters laying around here at the shop. Still have to figure out what these will fit.
Logged
5105H and 6400H in stock

Performance Outdoor Equipment
performanceoutdoorequipment.com
Dolmar, Echo, Jonsered

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22183
  • Karma: 560
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Echo bar adapters 12mm to 8mm D176
« Reply #12 on: August 10, 2015, 01:17:18 pm »
Sorry guys I keep forgetting to check the 6700.
Logged
REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2111
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Echo bar adapters 12mm to 8mm D176
« Reply #13 on: August 10, 2015, 03:12:12 pm »
Quote from: Nathaniel Vansickle on August 10, 2015, 09:14:51 am
i used to have a dozen of those "S" adapters laying around here at the shop. Still have to figure out what these will fit.


I just bought 10 of them (and 2 of the shorter ones used on Homelite Super E-Z and XL-101 series saws) from Joyce the Chainsawlady.  Had a few already, and couldn't pass up the chance to have a bunch more when she posted them for sale.

IIRC, GB cataloged their versions of the S clip recently.  The link to the GB catalog is in a thread here somewhere (IIRC, Cut4fun posted it).  If I remember right, one of their spacers is for the same D176 to D196/UXL adaptation, and they had 2 or 3 more clips (different thicknesses of wire) for other adaptations.  Now I need to find that thread...
Logged
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22183
  • Karma: 560
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Echo bar adapters 12mm to 8mm D176
« Reply #14 on: August 10, 2015, 03:43:28 pm »
Echo 6700 D176 bar mount area.

Logged
REDNECK Saw Repair Getter Done

Offline Nathaniel Vansickle

  • Piped Saw
  • *****
  • Posts: 468
  • Karma: 92
  • Location: Newcomerstown ,Ohio
Re: Echo bar adapters 12mm to 8mm D176
« Reply #15 on: August 10, 2015, 04:57:01 pm »
 ???
Logged
5105H and 6400H in stock

Performance Outdoor Equipment
performanceoutdoorequipment.com
Dolmar, Echo, Jonsered

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22183
  • Karma: 560
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Echo bar adapters 12mm to 8mm D176
« Reply #16 on: August 10, 2015, 07:59:03 pm »
Quote from: Nathaniel Vansickle on August 10, 2015, 04:57:01 pm
???

?

I showed 3 ways of reading it. ;) For fun. At  the shoulder on stud and loose not real tight.

1.894 is real close to yours 1.885
Logged
REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2111
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Echo bar adapters 12mm to 8mm D176
« Reply #17 on: August 10, 2015, 08:08:55 pm »
Interesting.
Logged
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22183
  • Karma: 560
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Echo bar adapters 12mm to 8mm D176
« Reply #18 on: August 10, 2015, 08:31:22 pm »
Seems they dont fit anything D176 we all have.  What does cannon say?
Logged
REDNECK Saw Repair Getter Done

Offline Nathaniel Vansickle

  • Piped Saw
  • *****
  • Posts: 468
  • Karma: 92
  • Location: Newcomerstown ,Ohio
Re: Echo bar adapters 12mm to 8mm D176
« Reply #19 on: August 17, 2015, 09:44:44 am »
I checked my 8000. It's the same as the 6700. coutesy of rmotoman over on AS. So I am putting a call in to Cannon to ask WTF they patterned these adapters off of as soon as they open today.
 
Logged
5105H and 6400H in stock

Performance Outdoor Equipment
performanceoutdoorequipment.com
Dolmar, Echo, Jonsered

Pages: 1 [2] 3 4   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
Echo 280

Started by Cut4fun . « 1 2 » Echo

10 Replies
1124 Views 		Last post May 21, 2013, 03:48:18 pm
by Cut4fun .
2 Replies
585 Views 		Last post February 06, 2012, 08:39:26 pm
by DB_43725
2 Replies
565 Views 		Last post July 13, 2015, 12:45:42 am
by Eccentric
7 Replies
295 Views 		Last post October 06, 2014, 09:32:58 am
by rusted bolts
Echo 340 T

Started by Cut4fun . « 1 2 3 » Echo

27 Replies
1239 Views 		Last post January 29, 2016, 09:06:32 pm
by Cut4fun .
6 Replies
169 Views 		Last post February 08, 2015, 05:51:03 pm
by Eccentric
22 Replies
598 Views 		Last post August 24, 2015, 08:50:24 pm
by Eccentric
6 Replies
437 Views 		Last post July 31, 2015, 12:26:53 pm
by Cut4fun .
15 Replies
380 Views 		Last post April 12, 2016, 04:20:49 pm
by sharkey
2 Replies
73 Views 		Last post October 05, 2020, 07:27:30 am
by Cut4fun