Author Topic: echo cs-310  (Read 580 times)

0 Members and 1 Guest are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21166
  • Karma: 474
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
echo cs-310
« on: September 29, 2015, 05:38:54 pm »
Had echo 310  dropped off today.  Reminds me of my echo 3900 physical size wise.   8)

Any known issues and tuning specs? Max rpm etc?

Guessing 31cc
REDNECK Saw Repair Getter Done

Share on Facebook Share on Twitter


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21166
  • Karma: 474
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: echo cs-310
« Reply #1 on: September 30, 2015, 12:31:39 pm »
@mountainlake or others that know.  Whats the good bads to watch and check on these?
REDNECK Saw Repair Getter Done

Offline Nathaniel Vansickle

  • Piped Saw
  • *****
  • Posts: 469
  • Karma: 92
  • Location: Newcomerstown ,Ohio
Re: echo cs-310
« Reply #2 on: September 30, 2015, 07:27:52 pm »
L mixture needle : 2 1/2, H mixture needle : 2 1/4  13k

only real problem i have had with them is the tank breaking at the front A/V mount/wrap handle mount. other than that they have been fairly reliable and run ok after a mm
5105H and 6400H in stock

Performance Outdoor Equipment
performanceoutdoorequipment.com
Dolmar, Echo, Jonsered


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21166
  • Karma: 474
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: echo cs-310
« Reply #3 on: September 30, 2015, 07:29:09 pm »
Thanks Nate.  I was holding off digging in till I got some info.  The L and H is good to know it is one of those. ;)
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21166
  • Karma: 474
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: echo cs-310
« Reply #4 on: October 01, 2015, 05:53:47 pm »
OK going to be truthful. Not impressed.  :o

I had to make sure it was 31cc = 30.5cc shown on tag. Saw is like new too.

I was just expecting it to be a little closer to my 39cc echo 3900.  I sure hope the echo 400 run little closer to the 3900 as the 310 isnt even  close.   :o
REDNECK Saw Repair Getter Done

Offline mountainlake

  • 5 cube
  • ***
  • Posts: 119
  • Karma: 21
Re: echo cs-310
« Reply #5 on: October 02, 2015, 07:43:08 am »

 I'm not impressed with the build quality of the 310  352 saws either and don't know how they run yet, I have one to put together .  The CS400 saws are real good runner and built good.  Steve

Online Fishnuts2

  • 4 cube
  • **
  • Posts: 52
  • Karma: 14
Re: echo cs-310
« Reply #6 on: October 02, 2015, 10:48:10 pm »
The 352 runs a lot better than the 310, they are quite different than the CS-400 though. I use the 352 often  limbing small stuff.


Sent from my iPhone using Tapatalk

Offline stubnail67

  • 6 cube
  • ****
  • Posts: 176
  • Karma: 22
Re: echo cs-310
« Reply #7 on: October 09, 2015, 08:36:01 pm »
what size bar ya have on the cs 310? 14 inch?

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21166
  • Karma: 474
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: echo cs-310
« Reply #8 on: October 09, 2015, 09:01:14 pm »
what size bar ya have on the cs 310? 14 inch?


Thats what was on it.   I was only cutting maybe 6" cherry at best. Just a dog this one was.

The little 30cc poulan 1800 would takes its lunch IMO.
REDNECK Saw Repair Getter Done

Offline stubnail67

  • 6 cube
  • ****
  • Posts: 176
  • Karma: 22
Re: echo cs-310
« Reply #9 on: October 09, 2015, 09:14:46 pm »
Dam i was going to buy one to add to my echo  line up.... maybe i should keep my poulan 2600.....

 

Related Topics

  Subject / Started by Replies Last post
Echo 452

Started by Cut4fun Echo

2 Replies
759 Views
Last post April 23, 2012, 11:19:35 pm
by DB_43725
Echo CS 60S

Started by Dh1984 Echo

4 Replies
1004 Views
Last post June 05, 2012, 06:33:11 pm
by Dh1984
1 Replies
260 Views
Last post October 27, 2012, 10:27:31 pm
by Al Smith
8 Replies
308 Views
Last post September 28, 2013, 03:47:02 pm
by Cut4fun .
Echo 290

Started by Cut4fun . Echo

1 Replies
245 Views
Last post September 19, 2013, 05:24:50 pm
by sharkey
2 Replies
480 Views
Last post July 13, 2015, 12:45:42 am
by Eccentric
7 Replies
270 Views
Last post October 06, 2014, 09:32:58 am
by rusted bolts
Echo 340 T

Started by Cut4fun . « 1 2 3 » Echo

27 Replies
1106 Views
Last post January 29, 2016, 09:06:32 pm
by Cut4fun .
6 Replies
371 Views
Last post July 31, 2015, 12:26:53 pm
by Cut4fun .
9 Replies
513 Views
Last post November 04, 2017, 08:43:38 pm
by Jaymo