Author Topic: Echo cs360T  (Read 679 times)

0 Members and 0 Guests are viewing this topic.

Offline DB_43725

  • 3 cube
  • *
  • Posts: 17
  • Karma: 1
Echo cs360T
« on: January 20, 2012, 02:54:34 pm »
Does anyone make any different drive sprockets for this saw ?

Share on Facebook Share on Twitter


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21166
  • Karma: 474
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Echo cs360T
« Reply #1 on: January 20, 2012, 06:19:36 pm »
I dont know this saw so I am looking into echo info. Echo nut username here is the echo go to guy.

This?   http://www.echo-usa.com/Products/Chain-Saws/CS-360T

6 IPL's depending on serial numbers.  http://www.echo-usa.com/Support-Help/Technical-Documents.aspx?s=CS-360T

I'm just going to pick one to see info.  First one shows a spur gear type clutch drum.  http://www.echo-usa.com/getattachment/07fbfc21-c570-4a7a-960b-ee38118437c5/CS360Te_09_010411.pdf

REDNECK Saw Repair Getter Done

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 3922
  • Karma: 143
  • OHIO REDNECK
Re: Echo cs360T
« Reply #2 on: January 20, 2012, 07:06:52 pm »
REDNECK Saw Repair

Offline DB_43725

  • 3 cube
  • *
  • Posts: 17
  • Karma: 1
Re: Echo cs360T
« Reply #3 on: January 21, 2012, 01:48:03 pm »
Thanks for all the help,,, What im looking for is a sproket that will fit it thats a 325 pitch,, I know now that echo doesnt make such an aminal,, but was hopeing some other manufacturer might be able to make it work. I picked up a realy nice bar for this saw and I would realy like to use it,,, but not paying close atention till I got it , seen its a 325 pitch instead of 3/8 low pro. So I set out and try to find something I might beable fit in their. Good thing is that listing on e bay shows it also fits another brand of saw, so maybe with any luck maybe that CO make one. This may be all for not anyway as the dern thing may not want to pull a larger chain,,LOL But I wont know unless I try. I was kinda thinking that when ever they bring out a new model they may use some parts the tooling has already been make to produce, or buy someones old tooling, Maybe Im wrong, but seems that might be cost effitive. I did find out Johnsonred makes a small sproket in 325 but I dont know about Dia and shaft size. Sorry for being so long winded here,but I was just looking for someone that might have a little intel.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21166
  • Karma: 474
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
REDNECK Saw Repair Getter Done

Offline mountainlake

  • 5 cube
  • ***
  • Posts: 119
  • Karma: 21
Re: Echo cs360T
« Reply #5 on: January 26, 2012, 07:21:47 pm »

 You'll find you cutting speed a lot slower with a .325 7 tooth setup.  Tried it both ways.   Steve

 

Related Topics

  Subject / Started by Replies Last post
Echo 8000

Started by RedBaron « 1 2 ... 6 7 » Echo

64 Replies
3749 Views
Last post September 15, 2017, 12:39:50 pm
by WLZecho8000P
5 Replies
1087 Views
Last post March 30, 2011, 10:46:44 pm
by Cut4fun .
20 Replies
6749 Views
Last post August 05, 2015, 05:12:03 pm
by Cut4fun .
9 Replies
6003 Views
Last post November 18, 2011, 06:29:34 pm
by brokenbudget
3 Replies
606 Views
Last post July 28, 2011, 08:51:43 am
by Al Smith
Echo 280

Started by Cut4fun . « 1 2 » Echo

10 Replies
1052 Views
Last post May 21, 2013, 03:48:18 pm
by Cut4fun .
9 Replies
980 Views
Last post March 04, 2015, 11:17:03 pm
by 660magnum
2 Replies
439 Views
Last post December 12, 2011, 06:47:38 pm
by Cut4fun .
2 Replies
548 Views
Last post February 06, 2012, 08:39:26 pm
by DB_43725
Echo CS346-345

Started by leec Echo

4 Replies
375 Views
Last post June 05, 2014, 08:22:37 pm
by leec