Author Topic: echo oiler  (Read 340 times)

0 Members and 0 Guests are viewing this topic.

Offline echo user

  • 4 cube
  • **
  • Posts: 60
  • Karma: 7
echo oiler
« on: December 22, 2015, 09:59:07 pm »
has anyone had any problems with a cs 8000 oiling too much  it runs oil on floor  and floods bar  while running

Share on Facebook Share on Twitter


Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4067
  • Karma: 162
  • OHIO REDNECK
Re: echo oiler
« Reply #1 on: December 23, 2015, 08:40:25 am »
I havent seen or heard of such.  Oiler line broken?

I always ran my oilers wide open and never problems. Long as there is still some bar oil in the tank to a  tank of fuel I am happy. 
REDNECK Saw Repair

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4067
  • Karma: 162
  • OHIO REDNECK
REDNECK Saw Repair

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4067
  • Karma: 162
  • OHIO REDNECK
Re: echo oiler
« Reply #3 on: December 23, 2015, 08:49:30 am »
echo 8000 IPL for oiler line reference  http://s30387.gridserver.com/partsDiagrams/Echo%20CS-8000%20and%20CS-8000P.pdf

Look at page 5 there is a triple hook up   
REDNECK Saw Repair

Offline echo user

  • 4 cube
  • **
  • Posts: 60
  • Karma: 7
Re: echo oiler
« Reply #4 on: December 27, 2015, 08:02:32 pm »
thank you

Offline sharkey

  • Piped Saw
  • *****
  • Posts: 367
  • Karma: 37
Re: echo oiler
« Reply #5 on: December 30, 2015, 01:53:59 am »
Yep that 8000 oiler can run the tank dry quick.  Most dont know that this saw was the first with a no oil at idle system.  This no oil at idle system was replaced with the brass worm gear on the crank that runs the pump all the time.  Who knows why the swapped out their old system.  Oil adjustment is on the right side near the cylinder in front of the handle support.  Forward is the lowest setting, adjustment is via a flat bladed screwdriver. 

Otherwise, if oil is seeping past the bottom grommet where the hose comes out of the tank, check the air inlet which is in the forward top corner behind the inner bar plate.  Older 8000's used a copper cotter pin as the vent whereas newer models have a duckbill in that same hole behind the inner bar plate.  May have plugged with saw dust and cant let the heat pressure out of the tank?   

 

Related Topics

  Subject / Started by Replies Last post
PP 655 Oiler

Started by blsnelling « 1 2 » Poulan

10 Replies
338 Views
Last post October 18, 2013, 11:20:35 pm
by blsnelling
166 oiler

Started by chadstone « 1 2 3 » Dolmar Makita

21 Replies
733 Views
Last post August 05, 2014, 07:38:22 pm
by Cut4fun
5 Replies
168 Views
Last post December 08, 2013, 05:47:14 pm
by Fish
2 Replies
158 Views
Last post January 10, 2014, 09:45:18 am
by Fish
338 oiler

Started by gunrac « 1 2 3 4 » Husqvarna

33 Replies
670 Views
Last post March 12, 2014, 03:43:04 pm
by KilliansRedLeo
7 Replies
346 Views
Last post April 01, 2014, 02:32:30 pm
by HolmenTree
8 Replies
117 Views
Last post October 25, 2015, 02:47:33 pm
by jmester
5 Replies
171 Views
Last post May 19, 2020, 06:58:09 pm
by 3000 FPS
5 Replies
468 Views
Last post January 19, 2017, 09:55:19 pm
by farmboy
5 Replies
91 Views
Last post July 13, 2020, 07:26:21 pm
by mowertech