Author Topic: Remove walbro carb screw limiters  (Read 3019 times)

0 Members and 33 Guests are viewing this topic.

Offline 7sleeper

  • 4 cube
  • **
  • Posts: 39
  • Karma: 10

  • Total Badges: 13
    Badges: (View All)
    Linux User Mobile User Level 3 One year Anniversary Karma Good 10 Posts
Remove walbro carb screw limiters
« on: February 03, 2014, 02:27:10 pm »
Dear community,

I have searched this forum and haven't found any info on the topic of this type of carb cap. I have also searched other forums but haven't found what I am looking for.

I am aware of using a dry wall screw to remove the "epa" caps but this model is more than resilient. It is on a walbro carb and I would like to remove it in a way as to reapply after correction. If I pull it I can only get it off 1-2mm. That's all. After that it just snaps in place and I could hang the saw from the limiter!
Any one an idea?

Here is a pic from the outside.




Thanks for the help!

7

p.s. it's about this saw


Share on Facebook Share on Twitter


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23699
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

  • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Remove walbro carb screw limiters
« Reply #1 on: February 03, 2014, 02:36:59 pm »
I just trim the plastic tabs of those. Using a dremel or knife.  Gives you full adjustments then.

Offline 7sleeper

  • 4 cube
  • **
  • Posts: 39
  • Karma: 10

  • Total Badges: 13
    Badges: (View All)
    Linux User Mobile User Level 3 One year Anniversary Karma Good 10 Posts
Re: Remove walbro carb screw limiters
« Reply #2 on: February 03, 2014, 04:13:03 pm »
Thanks was hoping to remove and be able to reinsert so that the possible changes are limited.

Will do a review here of the above saw soon.

7

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 150
  • Location: Hayesville, NC

  • Total Badges: 31
    Badges: (View All)
    Level 6 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary 1000 Posts Old Browser
Re: Remove walbro carb screw limiters
« Reply #3 on: February 06, 2014, 09:27:34 am »
Take carb off trim tabs off with razor knife in place.  You won't need to remove them.  Walbro does make a tool for pulling them.  I have the tool but never use it. Tool has two little pins that go in the little round holes to locate tool and hooks under the stops to pull against the stops.  After trimming stops tool is rendered useless nothing to pull against.  Just did 3 of those carbs recently.  HDA160 IIRC.  CS56, 156, 962, 162, 165 use the same carb.
Shep

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 150
  • Location: Hayesville, NC

  • Total Badges: 31
    Badges: (View All)
    Level 6 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary 1000 Posts Old Browser
Re: Remove walbro carb screw limiters
« Reply #4 on: February 06, 2014, 01:10:10 pm »
Fedex just dropped off a real nice 962.  Piston is scored.  Got a WP 162 P&C may drop it on it after I find out why it scored.  Was going to put it on a 156 with a 165 crank for a lighter 165.  I think the 962 has a dual port cyl. where the 162 is quad port.  I'll know tomorrow.
Shep

Offline 7sleeper

  • 4 cube
  • **
  • Posts: 39
  • Karma: 10

  • Total Badges: 13
    Badges: (View All)
    Linux User Mobile User Level 3 One year Anniversary Karma Good 10 Posts
Re: Remove walbro carb screw limiters
« Reply #5 on: February 07, 2014, 02:22:02 am »
Thanks for the info! But too late. After a few days trying to yank the tabs off with major force I simply gave up and ground off half of the tabs with my dremel clone. I adjusted the carb to H 13200 and L to 2700.
Fedex just dropped off a real nice 962.  Piston is scored.  Got a WP 162 P&C may drop it on it after I find out why it scored.  Was going to put it on a 156 with a 165 crank for a lighter 165.  I think the 962 has a dual port cyl. where the 162 is quad port.  I'll know tomorrow.
Shep
Waiting for your feedback!

7

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 150
  • Location: Hayesville, NC

  • Total Badges: 31
    Badges: (View All)
    Level 6 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary 1000 Posts Old Browser
Re: Remove walbro carb screw limiters
« Reply #6 on: February 12, 2014, 09:38:10 pm »
Pulled cyl on 962 this afternoon.  It was as I suspected dual port not quad port. 
Shep

 

Related Topics

  Subject / Started by Replies Last post
10 Replies
2199 Views
Last post November 10, 2017, 12:29:46 pm
by ray benson
19 Replies
4213 Views
Last post November 13, 2019, 10:54:28 am
by Cut4fun .
2 Replies
321 Views
Last post November 11, 2013, 01:39:25 pm
by sharkey
7 Replies
992 Views
Last post December 18, 2013, 12:25:10 pm
by KilliansRedLeo
15 Replies
912 Views
Last post February 20, 2014, 09:34:42 am
by KilliansRedLeo
7 Replies
566 Views
Last post December 12, 2015, 05:44:05 pm
by sharkey
3 Replies
792 Views
Last post October 06, 2015, 02:35:12 pm
by tassin85
1 Replies
488 Views
Last post March 02, 2016, 10:15:56 pm
by Ozarker
7 Replies
969 Views
Last post February 03, 2016, 02:37:56 pm
by Cut4fun .
1 Replies
465 Views
Last post October 20, 2019, 10:02:38 am
by Cut4fun .