Author Topic: Racesaws.com  (Read 4415 times)

0 Members and 0 Guests are viewing this topic.

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: Racesaws.com
« Reply #10 on: September 07, 2014, 07:45:16 pm »
Kev, my Racesaws.com stuff is long gone.   Real shame all that great info is MIA, i'll give Rick a shout and see if he or Craig have any of logo stuff saved. 


   

 

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4708
  • Karma: 320
  • Location: Carpenter, Wyoming
Re: Racesaws.com
« Reply #11 on: September 07, 2014, 10:50:37 pm »
Dang found a half of a sleeve of new racesaws hats too  :o.   Just sitting on shelf in barn in plastic still.    :-\

I still have my hat.   I wear it all the time.
PP 505, 475, 445.
Like Like x 1 View List

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: Racesaws.com
« Reply #12 on: September 08, 2014, 05:17:30 am »
I have mine too.
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .
Like Like x 1 View List

Offline mdavlee .

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1968
  • Karma: 171
Re: Racesaws.com
« Reply #13 on: September 08, 2014, 08:42:56 am »
Kevin I'd like to have one of those hats.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23987
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Racesaws.com
« Reply #14 on: September 08, 2014, 11:48:51 am »
Kevin I'd like to have one of those hats.

PM me your addy again.

Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2779
  • Karma: 181
Re: Racesaws.com
« Reply #15 on: September 08, 2014, 08:07:12 pm »
Concerning that site it started out good .Towards the end it became quite frankly a pissen match which was too bad it went that way .

I've heard the story right from the source and it should never have gone down that way. At any rate it caused a lot of hard feelings .Water over the dam at this point .

I haven't talked to Rick in a while so weather it gets running again is hard to say .Since though a few forums have popped up .The info is still there you just have to seperate the wheat from the chaff sometimes  ;)

Offline mdavlee .

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1968
  • Karma: 171
Re: Racesaws.com
« Reply #16 on: September 08, 2014, 08:29:00 pm »
There's still no site with all the race saw building stuff going on like there was then.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23987
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Racesaws.com
« Reply #17 on: September 10, 2014, 02:20:27 pm »
2008-2010 there was a wealth of knowledge shared there. Never was the same after the 1st meltdown when Helsel's wouldnt sell out to him and all the info lost on the take down. Just a shame it was all trusted to 1 POS ecsaws aka woodsjunkie with the keys and passwords. 

#2 RS was a total joke IMO and I wouldnt even go back as the POS was still admin.  Even told Rick and Cliff I wouldnt be back till he was gone.  POS wouldnt give Cliff the info to the site and took it down with him. Rick had the site turned off so they could start fresh without the POS ecsaws aka woodsjunkie. 

 #3 RS try was just that, all the energy and great folks had had enough of losing their info.



Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23987
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Racesaws.com
« Reply #18 on: September 10, 2014, 02:22:41 pm »
Mike when I shipped the hat. I didnt offer you the XL Manton Racesaws shirt because I figured you were in the same boat as me.

Offline mdavlee .

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1968
  • Karma: 171
Re: Racesaws.com
« Reply #19 on: September 10, 2014, 06:32:28 pm »
Yeah an XL won't help me out either.

 

Related Topics

  Subject / Started by Replies Last post
11 Replies
804 Views
Last post November 16, 2015, 07:33:53 am
by Totembear
12 Replies
840 Views
Last post December 29, 2015, 11:00:28 pm
by ej
22 Replies
1429 Views
Last post August 17, 2017, 07:04:48 pm
by Cut4fun .