« previous next »
Pages: [1]   Go Down

Author Topic: Homelite. UT-10045 super XL carb removal help??????  (Read 1787 times)

0 Members and 0 Guests are viewing this topic.

Offline Klute55

  • pruner
  • *
  • Posts: 4
  • Karma: 0
Homelite. UT-10045 super XL carb removal help??????
« on: May 08, 2012, 11:19:03 am »
I can not fig out how to remove the carb.  I have a rebuild kit for carb.  Piston is in great shape, compression is good but it will only run for 20 seconds.   So I want to rebuild carb. Wdc.   I disconnected throttle, fuel line and choke but can't seem to find where to disconnect carb.    No visible nuts or bolts.  And it is in there tight as if it was welded in place.  Thanks for your help in advance, I'm so happy I found this board.  Many knowledgable members!!!!!!   Thanks again.......
Logged

Share on Facebook Share on Twitter

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: Homelite. UT-10045 super XL carb removal help??????
« Reply #1 on: May 08, 2012, 12:25:17 pm »
Some these like the XL150, you have to remove the engine crankcase from the outer case.
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline Klute55

  • pruner
  • *
  • Posts: 4
  • Karma: 0
Re: Homelite. UT-10045 super XL carb removal help??????
« Reply #2 on: May 08, 2012, 03:32:56 pm »
I will send pics tomorrow of my homelite.   If I can figure out how........lol.  I'm new to this bulletin board stuff, it's challenging to navigate around......thanks
Logged

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: Homelite. UT-10045 super XL carb removal help??????
« Reply #3 on: May 08, 2012, 04:10:28 pm »
I upload my pictures to Photo Bucket and then link to them here. They are automatically properly sized that way. 

Here's a parts explosion of the chainsaw. You will need to copy and paste this line into a blank Internet address line in a new tab.

s30387.gridserver.com/partsDiagrams/Homelite%20Super%20XL-925.pdf
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21948
  • Karma: 533
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Homelite. UT-10045 super XL carb removal help??????
« Reply #4 on: May 08, 2012, 06:40:26 pm »
Logged
REDNECK Saw Repair Getter Done

Offline doc2358

  • 3 cube
  • *
  • Posts: 11
  • Karma: 1
Re: Homelite. UT-10045 super XL carb removal help??????
« Reply #5 on: January 29, 2013, 12:02:22 pm »
My first reply. I have 3 UT10045 saws All of mine have bolts thru the carb. from rear to front. Need a 5/16 wrench to remove them.
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
2 Replies
1008 Views 		Last post April 24, 2011, 02:10:10 am
by mcbob
2 Replies
175 Views 		Last post September 10, 2013, 03:38:21 pm
by Cut4fun .
2 Replies
524 Views 		Last post December 18, 2013, 11:36:20 pm
by Eccentric
4 Replies
211 Views 		Last post March 14, 2015, 08:38:33 pm
by man of stihl
5 Replies
441 Views 		Last post August 13, 2015, 07:47:55 pm
by ears54
28 Replies
1511 Views 		Last post March 31, 2019, 09:07:00 am
by super44
1 Replies
300 Views 		Last post February 09, 2016, 09:22:16 pm
by super44
5 Replies
402 Views 		Last post March 30, 2016, 04:04:54 pm
by deezlfan
0 Replies
153 Views 		Last post April 26, 2016, 09:48:52 am
by Cut4fun .
5 Replies
279 Views 		Last post March 21, 2019, 07:04:12 am
by waltergorman