Author Topic: 162 SE  (Read 355 times)

0 Members and 0 Guests are viewing this topic.

Offline trail twister

  • 5 cube
  • ***
  • Posts: 106
  • Karma: 18
162 SE
« on: August 01, 2016, 09:36:16 am »
Starter dawgs are bad on this saw my favorite. I've looked at it and It looks to me as if the pins that hold the dawgs in place are pressed in.
Any one know if this is correct?

 ;D  Al

Share on Facebook Share on Twitter


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21874
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 162 SE
« Reply #1 on: August 01, 2016, 09:59:09 am »
I dont know saw so just just looking stuff up.

husqvarna 162 IPL http://www.husqvarna.com/ddoc/HUSI/HUSI1979_AAaa/HUSI1979_AAaa_I7900005_.pdf

162sg flywheel shown




member Scott =  chainsawr store   https://store.chainsawr.com/products/husqvarna-162sg-chainsaw-flywheel-assembly-for-heated-handles
REDNECK Saw Repair Getter Done

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 149
  • Location: Hayesville, NC
Re: 162 SE
« Reply #2 on: August 01, 2016, 10:26:07 pm »
They are pressed in take a punch and drive them out from the back side of flywheel.  Replace needed parts and drive them back in with a hammer.
Shep

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: 162 SE
« Reply #3 on: August 02, 2016, 03:09:12 am »
Yep.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline trail twister

  • 5 cube
  • ***
  • Posts: 106
  • Karma: 18
Re: 162 SE
« Reply #4 on: August 02, 2016, 05:29:35 am »
thanks for confirming what I thought.

 ;D  Al


Offline trail twister

  • 5 cube
  • ***
  • Posts: 106
  • Karma: 18
Re: 162 SE
« Reply #6 on: August 04, 2016, 06:16:48 am »
Thought I would put up a picture of my 39 year old saw.





 ;D  Al
Like Like x 1 View List

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: 162 SE
« Reply #7 on: August 05, 2016, 11:09:04 pm »
I've got a 162SE as well.  Haven't done anything with it since a good friend gave it to me.  Even still has an intact and functional chainbrake clutch cover.  Interesting to check out the first saw of this series.  Just about everything is magnesium on 'em.  Very little plastic...
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline trail twister

  • 5 cube
  • ***
  • Posts: 106
  • Karma: 18
Re: 162 SE
« Reply #8 on: August 06, 2016, 04:58:51 am »
My 162 does not have a chain brake on it.

 ;D  Al

Offline president

  • 4 cube
  • **
  • Posts: 28
  • Karma: 5
Re: 162 SE
« Reply #9 on: August 06, 2016, 04:04:47 pm »
nice predecesor of the 61 .the 162se was a closed port cyl.and was a pro built saw
if yours is the duall thin ring ,its an earlier version.they share the same p/cs as the johnsereds 630
I love mine too!
Informative Informative x 1 View List