Author Topic: Husqvarna 2100  (Read 1081 times)

0 Members and 0 Guests are viewing this topic.

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4470
  • Karma: 274
  • Location: Carpenter, Wyoming
Re: Husqvarna 2100
« Reply #30 on: December 18, 2013, 04:16:02 pm »
All the air filter covers that I have seen are really expensive.  I have been looking for one myself.
There is a cylinder cover with the air filter cover on ebay for 150.00 right now.
PP 505, 475, 445.

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Husqvarna 2100
« Reply #31 on: December 18, 2013, 04:26:09 pm »
All the air filter covers that I have seen are really expensive.  I have been looking for one myself.
There is a cylinder cover with the air filter cover on ebay for 150.00 right now.

That one's been listed on and off for a few months at least.  There are a few more top covers on ebay right now.  No more AF covers at the moment.

http://www.ebay.com/sch/i.html?_trksid=p2050601.m570.l1313.TR11.TRC1.A0.Xhusqvarna+2100+top&_nkw=husqvarna+2100+top&_sacat=0&_from=R40
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22054
  • Karma: 546
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna 2100
« Reply #32 on: December 18, 2013, 04:40:00 pm »
Cant open and look at. Would be buying unseen, going by word and that pic only. No other info. 

No not that kind of cheap Aaron.   

I did find a place to get a echo D176 36" for $70 shipped if I buy 2.  Just waiting till after Christmas to look into it further.  May just get a D009 and be done with it for $75 shipped.
REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Husqvarna 2100
« Reply #33 on: December 18, 2013, 04:51:58 pm »
Cant open and look at. Would be buying unseen, going by word and that pic only. No other info. 

No not that kind of cheap Aaron.   

I did find a place to get a echo D176 36" for $70 shipped if I buy 2.  Just waiting till after Christmas to look into it further.  May just get a D009 and be done with it for $75 shipped.

I didn't mean that my end would totally cover the saw (not by a longshot....no matter how cheap you get it).  Meant that the dynamics would change (meaning I'd be the one kicking in more).   For starters; I also have a new 32" 3/8-.050G D009 bar. 

That's a great deal for those D176 and D009 bars.  Wouldja please PM me their info once you're done dealing with them?
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4100
  • Karma: 166
  • OHIO REDNECK
Re: Husqvarna 2100
« Reply #34 on: January 22, 2014, 09:11:12 pm »
I dont usually buy these ...... :o......  ;D (not wanting to ruffle any feathers)  ;D  .

Anyhow looking at this one missing some parts.  What you see is what I have seen only.   Guessing cylinder cover, af cover, filter.  Is there a filter box or anything else?

Known issues with these to ask about?

Your opinion of what one is worth to buy that looks like this (says runs great)?  Do you think I could find the parts to finish easily? 

Looks like top cover, AF, and AF cover.  There's no filter box.  Top covers aren't too hard to find.  Filters aren't either.  A good AF cover is HARD to find nowadays.  They were all broken or discarded.

Not many known issues.  The o-rings around/under the manual oiler pump can leak.  When that happens you get fuel in the bar oil tank.  The stock fuel tank vent is a complicated piece with NLA parts.  It is best replaced with a molded fuel line (they're still available for these........both OEM and aftermarket) with a white plastic Echo tank vent on the end of the line (in the carb box area).  Look out for stripped screw holes, especially for the handlebar mounting screws (both on the bottom, and on the right side).

If it runs great and the P/C are good (I'd be worried about the intake side being 'dusted' if he's been running it without a filter) then it's worth a couple Franklins.  Maybe a tad more.  Pull the muffler and look at the P/C through the port at least.  Rings are standard 56mm x 1.5mm.  You can replace 'em with Cabers or with OEM 394XP rings.  Crank bearings are standard 6203's.  Crank seals are the same ones used on 181/281/288 and 394/395 Husqvarnas.

If you get that thing cheap enough and don't wanna keep it.............well then the dynamics of that trade we've been talking about may change a tad. 8)

The guy finally got back to me :o ( I had forgot about it). Wants $197 to my door.   

 I do not want the saw now and it's up in Maine or NE area. So shipping is $$$

http://chainsawrepair.createaforum.com/index.php?action=dlattach;topic=2184.0;attach=4907;image
REDNECK Saw Repair

Offline Tractorsaw1

  • 6 cube
  • ****
  • Posts: 183
  • Karma: 25
  • Location: SHOW ME MO
Re: Husqvarna 2100
« Reply #35 on: January 27, 2014, 11:20:45 am »
Anyone check out the 2101xp on sc craigslist?  I proly really shouldn't do it, but is it worth $300 PHO?  His youtube video makes it look pretty sweet, don't know I can resist.

www.youtube.com/watch?v=Z2rH6KWnKzA&feature=c4-overview&list=UU4gy5qooGJFBWSqeZzpk3lQ

Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2753
  • Karma: 170
Re: Husqvarna 2100
« Reply #36 on: January 27, 2014, 01:52:52 pm »
That would be about typical .Choke it once then get off it .If you leave it choked say like most Stihls that thing will flood .It has a rather large Tillotson model HS carb that can move a lot of fuel .The one thing you don't want to do is tug on that thing for 20 minutes trying to start a flooded engine because it ain't no picnic for sure .

Online srcarr52

  • 6 cube
  • ****
  • Posts: 288
  • Karma: 93
  • Location: IA
Re: Husqvarna 2100
« Reply #37 on: January 27, 2014, 01:53:21 pm »
I have a decent shape a/f cover for a 2100 I'd be willing to part with.  No fading but it has the typical cracks coming up from the lower rear corners.  Shoot me an offer.

Offline Tractorsaw1

  • 6 cube
  • ****
  • Posts: 183
  • Karma: 25
  • Location: SHOW ME MO
Re: Husqvarna 2100
« Reply #38 on: January 27, 2014, 02:08:26 pm »
I don't own a 2100 yet that needs a filter cover, but i'm workin on it. ;D

Offline Tractorsaw1

  • 6 cube
  • ****
  • Posts: 183
  • Karma: 25
  • Location: SHOW ME MO
Re: Husqvarna 2100
« Reply #39 on: January 27, 2014, 04:09:34 pm »
Either everyone is tryin to buy it, or it is not good deal, no comments either way?

 

Related Topics

  Subject / Started by Replies Last post
1 Replies
531 Views
Last post July 06, 2011, 06:25:52 am
by Al Smith
Husqvarna 2100

Started by darren_palms « 1 2 ... 6 7 » Husqvarna

63 Replies
1338 Views
Last post April 25, 2015, 10:21:41 am
by Cut4fun .
0 Replies
165 Views
Last post January 18, 2013, 10:20:59 pm
by darren_palms
5 Replies
230 Views
Last post October 05, 2013, 01:44:26 am
by Eccentric
151 Replies
2755 Views
Last post October 23, 2019, 01:38:04 pm
by raumato01
10 Replies
470 Views
Last post August 15, 2014, 06:03:50 am
by man of stihl
41 Replies
1274 Views
Last post May 08, 2015, 12:14:40 pm
by aclarke
42 Replies
1036 Views
Last post May 03, 2018, 09:25:53 am
by Cut4fun .
13 Replies
402 Views
Last post May 15, 2015, 05:37:49 pm
by EHP
9 Replies
324 Views
Last post February 12, 2016, 06:47:54 pm
by 604f_1