Author Topic: Husqvarna 2100 2101 1100 298  (Read 2687 times)

0 Members and 0 Guests are viewing this topic.

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: 2100 no power in the cut
« Reply #50 on: July 31, 2014, 11:00:15 am »
Be worth a try running a non - captivated fulcrum on the carb.  You can cut the little ring that the lever engages off the diaphragm a polish the tab so it doesn't bind.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21942
  • Karma: 530
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 2100 no power in the cut
« Reply #51 on: July 31, 2014, 03:22:37 pm »
Kevin.  One more thing I thought of that would give erratic carburetion would be a bent fork on the metering needle /fulcrum.  The forks are often bent from the mfg.  Take a close look at that.   

Me and this 2100 is going to fight. I tell ya that right now. LOL  4th freaking pull the recoil rope let go.  All 2' of it.  I put 3' of super strong recoil rope back in it.

Cylinder bolts checked out and was thinking maybe gasket between cylinder block was missing. So I pulled all of that to make sure and back together.

Then starting tearing back into carb.  Adam I did find bent fork on 1 side of the needle.  Instead of straightening that one. I just pulled everything out of the carb except the welch plug.  Knowing it was working right with that one. Noticed the new check valve diaphragm material was a little different.  More the of rubber style I like then material style like in it.   

Sprayed carb cleaner through all the holes making sure everything was working and not blocked anywhere. All checked out.

3 pull on choke she popped. 1 pull after she is running idling PHO.  Now to test and see what happens.  Hopefully the run on yesterday was due to the bent fork around needle and not seals. 

The on/off switch works.


REDNECK Saw Repair Getter Done

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: 2100 no power in the cut
« Reply #52 on: July 31, 2014, 04:51:54 pm »
Kevin, if nothing else you ARE a persistant bugger!
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: 2100 no power in the cut
« Reply #53 on: July 31, 2014, 05:00:26 pm »
I'm not sure if you said you checked this but did you check the tank vent? That jred 490 I have had a bad vent and it would lose power in the cut.
Ron

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21942
  • Karma: 530
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 2100 no power in the cut
« Reply #54 on: July 31, 2014, 05:19:58 pm »
I thought of tank vent today too Thanks Ron.

I made 8 good cuts with 16" bar buried. Then went wanky. Like surging through cuts. Air leak in my mind. 

Did some testing with carb cleaner like winland showed in mweba video and found  air leak between intake block and carb around carb gasket.

I think I have her figured out now.  After comparing the **** intake block winland pulled off and new gaskets that come in kit.  ;)
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21942
  • Karma: 530
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 2100 no power in the cut
« Reply #55 on: July 31, 2014, 05:24:07 pm »
Just in case. I have never done seals on a 2100.   Any tips or info to share. 

This is the most I have looked at one before.
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21942
  • Karma: 530
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 2100 no power in the cut
« Reply #56 on: July 31, 2014, 07:09:44 pm »
 All day with this thing. But I think I won after this last test session after pulling a gasket off of one of my HS carbs and using instead of the supplied gasket in the kit that is wrong wrong wrong.  You cant see it when putting all together lining intake bolts up.

Noticed this thing is a GAS HOG.   But power to spare. I ran his fuel out yesterday, ran a tank of my mix yesterday-today and start on another tank of my mix this evening.

Then I noticed the 2100 laughing at me. I thought what the heck I'm going to :-\ :-X. The bar nuts were vibrating off and 1 was already in the weeds. Got out the magnet on rollers and located it.  Yep were going to fight if it stays around.  :D :D

Pics running my 16" 4 chits. 




REDNECK Saw Repair Getter Done

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: 2100 no power in the cut
« Reply #57 on: July 31, 2014, 10:05:31 pm »
Good job bud!

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21942
  • Karma: 530
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 2100 no power in the cut
« Reply #58 on: July 31, 2014, 11:42:48 pm »
Thanks  Adam.

Husqvarna  2100 Velocity stack  v stack

Roger maybe something can be had from K&N  http://www.knfilters.com/filteraccess.htm
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21942
  • Karma: 530
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
5 Replies
446 Views
Last post July 31, 2011, 12:00:53 pm
by Cut4fun .
1 Replies
530 Views
Last post July 06, 2011, 06:25:52 am
by Al Smith
3 Replies
371 Views
Last post October 30, 2012, 07:54:20 pm
by Cut4fun
Husqvarna 2100

Started by darren_palms « 1 2 ... 6 7 » Husqvarna

63 Replies
1316 Views
Last post April 25, 2015, 10:21:41 am
by Cut4fun .
Husqvarna 2100

Started by turbo885 « 1 2 3 4 5 » Husqvarna

46 Replies
1072 Views
Last post February 03, 2014, 05:04:02 pm
by Eccentric
11 Replies
1003 Views
Last post October 06, 2013, 10:12:00 pm
by stihls066
5 Replies
227 Views
Last post October 05, 2013, 01:44:26 am
by Eccentric
10 Replies
464 Views
Last post August 15, 2014, 06:03:50 am
by man of stihl
12 Replies
382 Views
Last post May 13, 2015, 06:41:55 pm
by SquareFile
1 Replies
87 Views
Last post May 24, 2018, 02:27:47 pm
by Cut4fun .