Author Topic: Husqvarna 2100 2101 1100 298  (Read 2677 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21893
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 2100 no power in the cut
« Reply #60 on: August 01, 2014, 12:19:46 pm »
Just got done testing it out today. Perrrrrect IMO.  Got the tune set to 4 stroking and clears up nice under load in the cut.  Just like I like.

You know when I pulled your plug that was in it in the beginning and switched one of my plugs in it, your plug looked lean to me. Stands to reason now that we know it had a air leak.
REDNECK Saw Repair Getter Done

Online 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4461
  • Karma: 273
  • Location: Carpenter, Wyoming
Re: 2100 no power in the cut
« Reply #61 on: August 01, 2014, 07:42:40 pm »
Those velocity stacks are pretty fancy Kevin.    Sounds like the 2100 is doing good.   Good job on figuring it out.
PP 505, 475, 445.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21893
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 2100 no power in the cut
« Reply #62 on: August 02, 2014, 11:18:59 am »
These were sent to me before I had found the air leak. 

winland are these block off plates specific for the 2100?    Pretty slick, never seen the husky oem block off plates up close. 

REDNECK Saw Repair Getter Done

Offline winland

  • 6 cube
  • ****
  • Posts: 215
  • Karma: 24
  • Location: 44883
    • Winland Boxers
Re: 2100 no power in the cut
« Reply #63 on: August 02, 2014, 11:26:42 am »

winland are these block off plates specific for the 2100?    Pretty slick, never seen the husky oem block off plates up close. 


Yes, they are suppose to be specific to the 2100 and a few others.
I was hoping they would come with short bolts.
Have to go to ACE hardware to get some.


Online 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4461
  • Karma: 273
  • Location: Carpenter, Wyoming
Re: 2100 no power in the cut
« Reply #64 on: August 02, 2014, 12:04:07 pm »
Those block off plates kind of remind me of the ones I have made.
PP 505, 475, 445.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21893
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 2100 no power in the cut
« Reply #65 on: August 02, 2014, 12:18:16 pm »

winland are these block off plates specific for the 2100?    Pretty slick, never seen the husky oem block off plates up close. 


Yes, they are suppose to be specific to the 2100 and a few others.
I was hoping they would come with short bolts.
Have to go to ACE hardware to get some.



Whats stuff like that cost if you dont mind sharing?
REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: 2100 no power in the cut
« Reply #66 on: August 02, 2014, 02:14:15 pm »
Kevin find the part # for the Husky tool you're interested in (found in the list below, and in the 2100 WS manual), and then search for that part # on any of the online Husqvarna parts sites.



http://www.husqvarna.com/ddoc/HUSI/HUSI2003_AAaa/HUSI2003_AAaa__1000000-01.pdf

-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21893
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 2100 no power in the cut
« Reply #67 on: August 02, 2014, 02:34:47 pm »
I forgot all about that link. Got it on HD and here somewhere too. Thanks for reminder.
REDNECK Saw Repair Getter Done

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: 2100 no power in the cut
« Reply #68 on: August 03, 2014, 11:57:16 am »
All day with this thing. But I think I won after this last test session after pulling a gasket off of one of my HS carbs and using instead of the supplied gasket in the kit that is wrong wrong wrong.  You cant see it when putting all together lining intake bolts up.

Noticed this thing is a GAS HOG.   But power to spare. I ran his fuel out yesterday, ran a tank of my mix yesterday-today and start on another tank of my mix this evening.

Then I noticed the 2100 laughing at me. I thought what the heck I'm going to :-\ :-X. The bar nuts were vibrating off and 1 was already in the weeds. Got out the magnet on rollers and located it.  Yep were going to fight if it stays around.  :D :D

Pics running my 16" 4 chits. 





I like how the hole is cut in the air filter cover rather than remove the cover. Just looks better IMO. Good job figuring out the issues Kevin.
Ron

Offline winland

  • 6 cube
  • ****
  • Posts: 215
  • Karma: 24
  • Location: 44883
    • Winland Boxers
Re: 2100 no power in the cut
« Reply #69 on: August 03, 2014, 01:49:45 pm »
A couple of photos of the actual problem that Kevin found was causing most if not all my problems.
The gasket that is supplied in the rebuild kit is not "oval" enough to cover.

Agree Agree x 1 Useful Useful x 1 View List

 

Related Topics

  Subject / Started by Replies Last post
5 Replies
443 Views
Last post July 31, 2011, 12:00:53 pm
by Cut4fun .
1 Replies
528 Views
Last post July 06, 2011, 06:25:52 am
by Al Smith
3 Replies
370 Views
Last post October 30, 2012, 07:54:20 pm
by Cut4fun
Husqvarna 2100

Started by darren_palms « 1 2 ... 6 7 » Husqvarna

63 Replies
1313 Views
Last post April 25, 2015, 10:21:41 am
by Cut4fun .
Husqvarna 2100

Started by turbo885 « 1 2 3 4 5 » Husqvarna

46 Replies
1071 Views
Last post February 03, 2014, 05:04:02 pm
by Eccentric
11 Replies
1001 Views
Last post October 06, 2013, 10:12:00 pm
by stihls066
5 Replies
226 Views
Last post October 05, 2013, 01:44:26 am
by Eccentric
10 Replies
462 Views
Last post August 15, 2014, 06:03:50 am
by man of stihl
12 Replies
380 Views
Last post May 13, 2015, 06:41:55 pm
by SquareFile
1 Replies
84 Views
Last post May 24, 2018, 02:27:47 pm
by Cut4fun .