Author Topic: 3120 unlimited coil source (Read 1630 times)

Cut4fun . · « **Reply #10 on:** March 14, 2016, 01:07:31 pm »

I know when I tested my black coil on my older stock 3120 it started bumping limiter at 10500.

I heard of the newer ones in the 9600 that folks were complaining about. I also heard of the ones that were in the 12000 limit too.

snowsalot · « **Reply #11 on:** March 21, 2016, 07:36:00 am »

Just checked and mine has a Green coil the numbers on it are;

49 110 01
5440188-01
W36/08

i believe it is limited at 9000 but don't have RPM Gauge.

Also the number on the flywheel is;

5018950-02
070806

The tag on saw says

965 96 07-00
s/n 09 1900149

I believe this saw is an 2007 model but not sure.
I will post pics when i figure out how.

thanks guys.

i will post pics when i figure out how

snowsalot · « **Reply #12 on:** March 21, 2016, 07:51:26 am »

Trying this

mdavlee . · « **Reply #13 on:** March 21, 2016, 06:21:00 pm »

09 week 19

fullskip · « **Reply #14 on:** April 11, 2016, 08:17:28 pm »

I used to have one with a 60in bar on it that I sold oh maybe 15 years ago. It was only used when we had to jack big timber on bad ground. I put a 262xp coil in mine and JB'ed the high speed jet and drilled a smaller hole. It was maybe a third smaller can't remember the exact size. It just had a mild muff mod, it pulled the 60 well with fullskip 3/8ths.. I hated 404 because I did a lot of boring cutting jackseats...

Fullskip

fullskip · « **Reply #15 on:** April 14, 2016, 10:17:04 am »

On the above post I meant the high speed jet not the main.... sorry guy I guess iv been working to hard..

Fullskip

snowsalot · « **Reply #16 on:** May 12, 2016, 07:04:21 pm »

Installed a new AM coil for 272 today. Saw starts runs and idles. Revs up great, no limiter. Did not run it long as when I checked plug it is running a little lean. Will measure rpm tomorrow after I decide how much to open up the high speed jet.
The biggest problem right now is plug wire is too short, any suggestions on the best way to lengthen?

Sent from my SM-G900W8 using Tapatalk

Cut4fun . · « **Reply #17 on:** May 12, 2016, 08:03:44 pm »

Quote from: snowsalot on May 12, 2016, 07:04:21 pm

Installed a new AM coil for 272 today. Saw starts runs and idles. Revs up great, no limiter. Did not run it long as when I checked plug it is running a little lean. Will measure rpm tomorrow after I decide how much to open up the high speed jet.
The biggest problem right now is plug wire is too short, any suggestions on the best way to lengthen?

Sent from my SM-G900W8 using Tapatalk

I cant remember. But does the 272 lead just unscrew like the others? If so unscrew and put on longer lead.

snowsalot · « **Reply #18 on:** May 12, 2016, 08:19:47 pm »

This is the AM coil that I got , I was expecting made in China but this one appears to be made in Italy. Anyone used these before?

Sent from my SM-T330NU using Tapatalk

Cut4fun . · « **Reply #19 on:** May 12, 2016, 08:32:58 pm »

I got one for a 268 272 .

Chainsaw Repair

News:

Author Topic: 3120 unlimited coil source (Read 1630 times)

Cut4fun .

Re: 3120 unlimited coil source

snowsalot

Re: 3120 unlimited coil source

snowsalot

Re: 3120 unlimited coil source

mdavlee .

Re: 3120 unlimited coil source

fullskip

Re: 3120 unlimited coil source

fullskip

Re: 3120 unlimited coil source

snowsalot

Re: 3120 unlimited coil source

Cut4fun .

Re: 3120 unlimited coil source

snowsalot

Re: 3120 unlimited coil source

Cut4fun .

Re: 3120 unlimited coil source

Related Topics