Author Topic: 3120 unlimited coil source  (Read 2981 times)

0 Members and 40 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23708
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

  • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: 3120 unlimited coil source
« Reply #10 on: March 14, 2016, 01:07:31 pm »
I know when I tested my black coil on my older stock 3120 it started bumping limiter at 10500.

I heard of the newer ones in the 9600 that folks were complaining about. I also heard of the ones that were in the 12000 limit too.

Offline snowsalot

  • 3 cube
  • *
  • Posts: 16
  • Karma: 2

  • Total Badges: 8
    Badges: (View All)
    10 Posts Level 2 Karma Topic Starter Level 1 First Post
Re: 3120 unlimited coil source
« Reply #11 on: March 21, 2016, 07:36:00 am »
Just checked and mine has a Green coil the numbers on it are;

49 110 01
5440188-01
W36/08

i believe it is limited at 9000 but don't have RPM Gauge.

Also the number on the flywheel is;

5018950-02
070806

The tag on saw says

965 96 07-00
s/n 09 1900149

I believe this saw is an 2007 model but not sure.
I will post pics when i figure out how.

thanks guys.

i will post pics when i figure out how

Offline snowsalot

  • 3 cube
  • *
  • Posts: 16
  • Karma: 2

  • Total Badges: 8
    Badges: (View All)
    10 Posts Level 2 Karma Topic Starter Level 1 First Post
Re: 3120 unlimited coil source
« Reply #12 on: March 21, 2016, 07:51:26 am »
Trying this

Offline mdavlee .

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1968
  • Karma: 171

  • Total Badges: 31
    Badges: (View All)
    Level 6 Sixth year Anniversary Fifth year Anniversary 1000 Posts Fourth year Anniversary 500 Posts
Re: 3120 unlimited coil source
« Reply #13 on: March 21, 2016, 06:21:00 pm »
09 week 19

Offline fullskip

  • pruner
  • *
  • Posts: 2
  • Karma: 1

  • Total Badges: 10
    Badges: (View All)
    Linux User Mobile User First Post Karma Level 2 Second year Anniversary
Re: 3120 unlimited coil source
« Reply #14 on: April 11, 2016, 08:17:28 pm »
I used to have one with a 60in bar on it that I sold oh maybe 15 years ago. It was only used when we had to jack big timber on bad ground. I put a 262xp coil in mine and JB'ed the high speed jet and drilled a smaller hole. It was maybe a third smaller can't remember the exact size. It just had a mild muff mod, it pulled the 60 well with fullskip 3/8ths..  I hated 404 because I did a lot of boring cutting jackseats...

Fullskip
Informative Informative x 1 View List

Offline fullskip

  • pruner
  • *
  • Posts: 2
  • Karma: 1

  • Total Badges: 10
    Badges: (View All)
    Linux User Mobile User First Post Karma Level 2 Second year Anniversary
Re: 3120 unlimited coil source
« Reply #15 on: April 14, 2016, 10:17:04 am »
On the above post I meant the high speed jet not the main.... sorry guy I guess iv been working to hard..

Fullskip

Offline snowsalot

  • 3 cube
  • *
  • Posts: 16
  • Karma: 2

  • Total Badges: 8
    Badges: (View All)
    10 Posts Level 2 Karma Topic Starter Level 1 First Post
Re: 3120 unlimited coil source
« Reply #16 on: May 12, 2016, 07:04:21 pm »
Installed a new AM coil for 272 today. Saw starts runs and idles. Revs up great, no limiter. Did not run it long as when I checked plug it is running a little lean. Will measure rpm tomorrow after I decide how much to open up the high speed jet.
The biggest  problem right now is plug wire is too short, any suggestions on the best way to lengthen?

Sent from my SM-G900W8 using Tapatalk

Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23708
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

  • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: 3120 unlimited coil source
« Reply #17 on: May 12, 2016, 08:03:44 pm »
Installed a new AM coil for 272 today. Saw starts runs and idles. Revs up great, no limiter. Did not run it long as when I checked plug it is running a little lean. Will measure rpm tomorrow after I decide how much to open up the high speed jet.
The biggest  problem right now is plug wire is too short, any suggestions on the best way to lengthen?

Sent from my SM-G900W8 using Tapatalk



I cant remember. But does the 272 lead just unscrew like the others?  If so  unscrew and put on longer lead.

Offline snowsalot

  • 3 cube
  • *
  • Posts: 16
  • Karma: 2

  • Total Badges: 8
    Badges: (View All)
    10 Posts Level 2 Karma Topic Starter Level 1 First Post
Re: 3120 unlimited coil source
« Reply #18 on: May 12, 2016, 08:19:47 pm »
This is the AM coil that I got , I was expecting made in China but this one appears to be made in Italy.  Anyone used these before?

Sent from my SM-T330NU using Tapatalk


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23708
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

  • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: 3120 unlimited coil source
« Reply #19 on: May 12, 2016, 08:32:58 pm »
I got one for a 268 272 .

 

Related Topics

  Subject / Started by Replies Last post
4 Replies
1938 Views
Last post February 28, 2015, 11:59:49 am
by Cut4fun
0 Replies
338 Views
Last post August 11, 2011, 04:07:35 pm
by Roanoker494
43 Replies
2972 Views
Last post January 26, 2016, 01:16:30 pm
by Cut4fun .
8 Replies
525 Views
Last post January 22, 2014, 11:23:10 pm
by jockeydeuce
17 Replies
2508 Views
Last post February 14, 2014, 10:46:23 am
by 660magnum
12 Replies
3745 Views
Last post March 27, 2016, 01:48:26 pm
by gregh
8 Replies
481 Views
Last post April 27, 2014, 01:11:55 pm
by KilliansRedLeo
23 Replies
1948 Views
Last post November 04, 2014, 03:13:07 pm
by bloodontheice
7 Replies
417 Views
Last post December 15, 2014, 01:28:20 pm
by 660magnum
16 Replies
1841 Views
Last post May 06, 2017, 10:33:19 am
by Cut4fun .