Author Topic: Help identifying Husqvarna chainsaw  (Read 598 times)

0 Members and 0 Guests are viewing this topic.

Online srcarr52

  • 6 cube
  • ****
  • Posts: 288
  • Karma: 93
  • Location: IA
Re: Help identifying Husqvarna chainsaw
« Reply #10 on: November 25, 2013, 10:44:10 am »
]
As I said elsewhere it is a "frankensaw", that most likely is a 66 with a 266xp starter cover.  ;)

Did the 66 have closed transfer ports?  If not then that is a 266XP cylinder.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22055
  • Karma: 546
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Help identifying Husqvarna chainsaw
« Reply #11 on: November 25, 2013, 12:44:07 pm »
Just showing the pic of the 66 cylinder that I had in past.  These are all the pics I can find as this saw was sent to Finland if I recall right and cylinder never removed. Look like new inside still.
Sorry no pic of flywheel side like his pic was.
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22055
  • Karma: 546
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Help identifying Husqvarna chainsaw
« Reply #12 on: November 25, 2013, 12:56:50 pm »
266 cylinder to show it.

REDNECK Saw Repair Getter Done

Offline SawTroll

  • Nitro Hotsaw
  • *******
  • Posts: 1196
  • Karma: 68
  • Information collector
  • Location: Troms, North Norway
Re: Help identifying Husqvarna chainsaw
« Reply #13 on: November 25, 2013, 05:02:06 pm »
]
As I said elsewhere it is a "frankensaw", that most likely is a 66 with a 266xp starter cover.  ;)

Did the 66 have closed transfer ports?  If not then that is a 266XP cylinder.

No it didn't - it had basically the same open port Gilardoni as the non-xp 268.

Are you sure that is a closed port cylinder, and how do you know? 

Maybe you looked at the wrong picture? ???

Offline SawTroll

  • Nitro Hotsaw
  • *******
  • Posts: 1196
  • Karma: 68
  • Information collector
  • Location: Troms, North Norway
Re: Help identifying Husqvarna chainsaw
« Reply #14 on: November 25, 2013, 05:12:59 pm »
266 cylinder to show it.



...and that is a closed port Mahle...

Online srcarr52

  • 6 cube
  • ****
  • Posts: 288
  • Karma: 93
  • Location: IA
Re: Help identifying Husqvarna chainsaw
« Reply #15 on: December 03, 2013, 01:47:31 pm »
No it didn't - it had basically the same open port Gilardoni as the non-xp 268.

Are you sure that is a closed port cylinder, and how do you know? 

Maybe you looked at the wrong picture? ???

The outside of the transfer port bulges outward to make room for the transfer bridge. 

Offline SawTroll

  • Nitro Hotsaw
  • *******
  • Posts: 1196
  • Karma: 68
  • Information collector
  • Location: Troms, North Norway
Re: Help identifying Husqvarna chainsaw
« Reply #16 on: December 05, 2013, 11:50:18 am »
No it didn't - it had basically the same open port Gilardoni as the non-xp 268.

Are you sure that is a closed port cylinder, and how do you know? 

Maybe you looked at the wrong picture? ???

The outside of the transfer port bulges outward to make room for the transfer bridge. 


Are you sure that there is no bulge on the open port Gilardoni?

That doesn't really make sense to me - but then I don't know it all.... ;D

If Spike60 turned up here, I'm sure he could clear this little "dispute" up in an instant....

Offline SawTroll

  • Nitro Hotsaw
  • *******
  • Posts: 1196
  • Karma: 68
  • Information collector
  • Location: Troms, North Norway
Re: Help identifying Husqvarna chainsaw
« Reply #17 on: January 02, 2014, 08:07:26 am »

The outside of the transfer port bulges outward to make room for the transfer bridge. 


Well, I just found an old picture I had saved (hard-copy only) of an open loop Gilardoni, and it surely has such bulges where the transfers are, just like the cylinder in question here.
That one was off a non-xp 268, but that one used the same cylinder as the 66.

 

Related Topics

  Subject / Started by Replies Last post
8 Replies
2311 Views
Last post December 12, 2013, 02:33:48 pm
by Cut4fun .
33 Replies
3169 Views
Last post May 21, 2014, 07:49:28 am
by pete
19 Replies
588 Views
Last post February 24, 2017, 05:14:56 am
by dutchsawdoctor
20 Replies
348 Views
Last post February 28, 2014, 03:43:56 pm
by SawTroll
10 Replies
412 Views
Last post June 20, 2014, 08:36:08 am
by SawTroll
14 Replies
516 Views
Last post July 01, 2014, 05:05:20 pm
by radco
11 Replies
411 Views
Last post November 08, 2014, 10:27:28 pm
by Eccentric
2 Replies
113 Views
Last post March 09, 2015, 08:52:32 pm
by fuzz1500
0 Replies
191 Views
Last post April 19, 2017, 01:05:45 pm
by Cut4fun
1 Replies
213 Views
Last post November 28, 2019, 06:02:46 pm
by Philbert