« previous next »
Pages: [1]   Go Down

Author Topic: can i put a 372 jug on a 570 there junk stroke the same  (Read 477 times)

0 Members and 0 Guests are viewing this topic.

Offline huguenot ny

  • 3 cube
  • *
  • Posts: 5
  • Karma: 0
can i put a 372 jug on a 570 there junk stroke the same
« on: May 22, 2012, 01:41:08 am »
just wondering if i can do this on my 570 the things a piece of junk new ring good compression pops every time you pull it just will not go never been stumped with saws before this thing is garbage can even get new ring to seat good compression 120 with 1 pul pops 3 pulls she is at 140-145 but still only pops what is going on with this thing. help me i am pulling out my hair and i have none.
Logged

Share on Facebook Share on Twitter

Offline rms61moparman

  • 6 cube
  • ****
  • Posts: 270
  • Karma: 38
  • Location: Franklinton, Kentucky
Re: can i put a 372 jug on a 570 there junk stroke the same
« Reply #1 on: May 22, 2012, 03:12:17 am »

Sounds like a timing issue.
Have you checked the flywheel, keyway and crank?


Mike
Logged

Offline mweba

  • Piped Saw
  • *****
  • Posts: 392
  • Karma: 55
Re: can i put a 372 jug on a 570 there junk stroke the same
« Reply #2 on: May 22, 2012, 01:11:59 pm »
Will it run when primed?  Do you have a know good ignition to swap onto the saw?  145psi is normal for these saws and plenty of compression to run well.


Is there any play in the bearings?
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23416
  • Karma: 661
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: can i put a 372 jug on a 570 there junk stroke the same
« Reply #3 on: May 22, 2012, 01:50:26 pm »
WAG: have you checked seals etc for leaks.

Did you figure out why it needed rebuild (what had caused problems in first place). How was it running before you pulled it down etc.
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
14 Replies
1389 Views 		Last post November 03, 2022, 04:00:11 pm
by Cut4fun .
13 Replies
2196 Views 		Last post January 28, 2014, 06:23:28 pm
by 660magnum
6 Replies
587 Views 		Last post February 11, 2015, 04:57:38 pm
by dutchsawdoctor
11 Replies
1214 Views 		Last post December 25, 2019, 11:35:14 am
by Heavycutter66
11 Replies
658 Views 		Last post November 23, 2016, 11:13:02 pm
by oldpro
0 Replies
187 Views 		Last post May 18, 2015, 01:46:12 pm
by Cut4fun .
4 Replies
428 Views 		Last post July 24, 2015, 11:55:16 pm
by 3000 FPS
7 Replies
943 Views 		Last post March 10, 2016, 06:30:18 pm
by Philbert
8 Replies
4357 Views 		Last post May 14, 2016, 01:07:44 pm
by Cut4fun .
3 Replies
413 Views 		Last post June 01, 2018, 02:18:54 pm
by Cut4fun .