Author Topic: Husqvarna 350 options  (Read 3769 times)

0 Members and 0 Guests are viewing this topic.

Offline 350XP

  • 4 cube
  • **
  • Posts: 46
  • Karma: 4
  • Location: S.Newbury NH
Re: Husqvarna 350 options
« Reply #100 on: February 23, 2014, 07:22:47 pm »
then i did this one, even scored it rips, you can see the score marks
2004 husky 350XP
2004 346xp
2006 346xp
2004 359
husky 55
husky 51
2012 372 x-torq now a non x-torq
1988 266xp
2001 husky 136,now a 142
a couple of stihls

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22584
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna 350 options
« Reply #101 on: February 23, 2014, 07:34:43 pm »
Just seen that was a photobucket video in post before. Sounds good.
REDNECK Saw Repair Getter Done

Offline JohnG28

  • Piped Saw
  • *****
  • Posts: 315
  • Karma: 27
Re: Husqvarna 350 options
« Reply #102 on: February 23, 2014, 11:34:41 pm »
That's a nice looking job. Is that the same saw in the other videos also? Wondering because in one it said it was an am cylinder and wondering how it was before you started? Finally done with work for the week(end) and should be good to try to get mine fired up tomorrow. Don't have anything to do a muffler mod, but if I can make the 288 deflector workable somewhere tomorrow I'll steal it off my 361 till I can get another one. 361 is put up right now anyway. I didn't go crazy in the TP on this, just a little cleaner and wider towards the back on each. I don't think there's much out back to cut at all right now, have to take a look. Most of the snow melted the last few days so I think I can actually get through the yard now and see what I got! Been buried for a while! If I can I'll get some video up.

Offline 350XP

  • 4 cube
  • **
  • Posts: 46
  • Karma: 4
  • Location: S.Newbury NH
Re: Husqvarna 350 options
« Reply #103 on: February 24, 2014, 05:49:35 am »
its a AM one in the vid. heres my muff mod
2004 husky 350XP
2004 346xp
2006 346xp
2004 359
husky 55
husky 51
2012 372 x-torq now a non x-torq
1988 266xp
2001 husky 136,now a 142
a couple of stihls

 

Related Topics

  Subject / Started by Replies Last post
6 Replies
491 Views
Last post March 17, 2012, 11:06:21 pm
by Al Smith
11 Replies
1134 Views
Last post May 18, 2012, 10:03:11 pm
by Al Smith
8 Replies
1321 Views
Last post September 15, 2012, 02:02:54 pm
by Cut4fun .
8 Replies
790 Views
Last post September 18, 2012, 03:51:15 pm
by Cut4fun .
6 Replies
247 Views
Last post January 11, 2014, 04:10:04 pm
by procarbine2k1
117 Replies
2480 Views
Last post February 25, 2014, 01:59:38 pm
by JohnG28
064 carb options?

Started by gunnusmc03 « 1 2 » Stihl

11 Replies
930 Views
Last post February 15, 2014, 11:19:42 am
by jacob j.
6 Replies
206 Views
Last post February 24, 2014, 10:30:11 am
by srcarr52
10 Replies
636 Views
Last post September 22, 2015, 09:59:55 pm
by ch74
15 Replies
1346 Views
Last post March 10, 2016, 02:51:43 pm
by Cut4fun .