Author Topic: 350 rebuild, with some different parts.  (Read 194 times)

0 Members and 0 Guests are viewing this topic.

Offline alsled

  • Piped Saw
  • *****
  • Posts: 307
  • Karma: 18
350 rebuild, with some different parts.
« on: November 28, 2013, 09:38:24 am »
Got this 350 that was run with straight gas, 40 psi compression, so,, 
I had another good 350 jug and I opened up the exhaust port, left the height the same, also opened up the intake ports down by the crank.
The stock 350 piston is dished out in the middle, stock from the factory like this, i don't know the reason why???  I used a 45 mm piston out of a 55, flat top, with a caber ring.
No base gasket just gasket in a tube, 180 psi comp.  Its out side idling now.  Will report back when it gets into some wood.

Share on Facebook Share on Twitter


Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: 350 rebuild, with some different parts.
« Reply #1 on: November 28, 2013, 11:14:47 am »
Cool Al

Definitely let us know how it goes. Have you gotten the BB or the 394 into wood yet?
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline alsled

  • Piped Saw
  • *****
  • Posts: 307
  • Karma: 18
Re: 350 rebuild, with some different parts.
« Reply #2 on: November 28, 2013, 11:22:42 am »
Going to my buddy in Pike Ny. Saturday. He had a load of logs

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: 350 rebuild, with some different parts.
« Reply #3 on: November 28, 2013, 11:52:46 am »
Be Careful!  NEVER CUT ALONE!!!!

 :D ;D :D ;D
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline rms61moparman

  • 6 cube
  • ****
  • Posts: 270
  • Karma: 38
  • Location: Franklinton, Kentucky
Re: 350 rebuild, with some different parts.
« Reply #4 on: November 28, 2013, 01:04:54 pm »
Got this 350 that was run with straight gas, 40 psi compression, so,, 
I had another good 350 jug and I opened up the exhaust port, left the height the same, also opened up the intake ports down by the crank.
The stock 350 piston is dished out in the middle, stock from the factory like this, i don't know the reason why???  I used a 45 mm piston out of a 55, flat top, with a caber ring.
No base gasket just gasket in a tube, 180 psi comp.  Its out side idling now.  Will report back when it gets into some wood.


The cratered piston was from the E.P.A. models of 350. Not sure what difference the dish makes but that is the reason. I put the piston out of a 353 in mine and it just ran fantastic. It would still have a home here if it weren't for the screw down top cover. I sold the 350 and bought a 351, put an oe 346 top end on it and that saw is a little jewel. Like the clip on top much better.


Mike

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2112
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northwestern Wyoming
Re: 350 rebuild, with some different parts.
« Reply #5 on: November 28, 2013, 02:03:25 pm »
Got this 350 that was run with straight gas, 40 psi compression, so,, 
I had another good 350 jug and I opened up the exhaust port, left the height the same, also opened up the intake ports down by the crank.
The stock 350 piston is dished out in the middle, stock from the factory like this, i don't know the reason why???  I used a 45 mm piston out of a 55, flat top, with a caber ring.
No base gasket just gasket in a tube, 180 psi comp.  Its out side idling now.  Will report back when it gets into some wood.


The cratered piston was from the E.P.A. models of 350. Not sure what difference the dish makes but that is the reason. I put the piston out of a 353 in mine and it just ran fantastic. It would still have a home here if it weren't for the screw down top cover. I sold the 350 and bought a 351, put an oe 346 top end on it and that saw is a little jewel. Like the clip on top much better.

Mike

The EPA 350's were 45mm (with "45" stamped on top of the cylinder, and removable transfer covers) and can take a flat top 353 piston like you stated.  The EPA 350 cylinders are almost identical to a 353 cylinder, although the part #'s for the two are slightly different.  The older 350's have a 44mm cylinder and a flat top piston (and don't have removable transfer covers).

Offline alsled

  • Piped Saw
  • *****
  • Posts: 307
  • Karma: 18
Re: 350 rebuild, with some different parts.
« Reply #6 on: November 30, 2013, 02:55:09 pm »
I ran the saw today and was very happy with it, it does spin more rpm and feels stronger then my 51 open port 44mm saws for sure.

 

Related Topics

  Subject / Started by Replies Last post
3 Replies
384 Views
Last post June 30, 2012, 10:04:41 am
by mgshiho
8 Replies
613 Views
Last post February 01, 2013, 03:10:13 pm
by 660magnum
4 Replies
205 Views
Last post November 07, 2013, 10:09:10 pm
by Gregsl
2 Replies
219 Views
Last post November 08, 2013, 05:50:01 am
by sharkey
12 Replies
550 Views
Last post November 16, 2013, 06:47:39 am
by NHRA1877
19 Replies
396 Views
Last post December 10, 2013, 08:38:12 pm
by jmester
394 Rebuild and BB

Started by alsled « 1 2 ... 5 6 » Husqvarna

51 Replies
946 Views
Last post June 13, 2014, 10:49:39 pm
by KilliansRedLeo
1 Replies
317 Views
Last post June 08, 2014, 08:01:59 am
by jmester
2165 Rebuild

Started by mdavlee . « 1 2 3 » Jonsered

22 Replies
907 Views
Last post January 09, 2016, 11:33:44 am
by mdavlee .
3 Replies
240 Views
Last post March 05, 2016, 10:21:43 pm
by jmester