Author Topic: 372 rings  (Read 521 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4084
  • Karma: 165
  • OHIO REDNECK
372 rings
« on: December 08, 2011, 07:39:03 pm »
Just trying to confirm.

503289042  372 ring is 50mm 1.5mm  ?  Was this the one used on the single ring piston.


503289036  372 ring is the 50mm 1.2mm one that is used on the 2 ring piston?

Getting all my numbers confused in my head now days.  :-[ :P
REDNECK Saw Repair

Share on Facebook Share on Twitter


Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: 372 rings
« Reply #1 on: December 09, 2011, 08:09:05 am »
Yes. The 1.2 mm is the two EPA rings and 1.5 mm is the single ring. As long as your installing them in a OEM piston. Some after market pistons may vary. Like the NWP single ring piston uses the 1.2 mm.
Ron

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 372 rings
« Reply #2 on: December 09, 2011, 01:16:37 pm »
I was just trying to make sure I had the right part numbers with right rings.   I almost ordered 8 of the 1.5mm and I wanted 1.2mm.   
REDNECK Saw Repair Getter Done

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4084
  • Karma: 165
  • OHIO REDNECK
Re: 372 rings
« Reply #3 on: December 10, 2011, 04:02:38 pm »
Just looking at other rings out there.

Have any of you ran these rings and what is your say, good or bad etc?

Ductile Split Groove Piston Rings  http://www.baileysonline.com/itemdetail.asp?item=PRSD+5012&catID=

Caber F-Cast Piston Rings http://www.baileysonline.com/itemdetail.asp?item=CRF+5012&catID=

REDNECK Saw Repair

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: 372 rings
« Reply #4 on: December 10, 2011, 05:21:09 pm »
The caber rings are my favorite. Didn't know baileys sold them. I always got them from that Greek guy. There supposed to be better than OEM. I have not tried the NWP.
Ron

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 372 rings
« Reply #5 on: December 10, 2011, 05:39:39 pm »
Greek guy.

Always wondered about this  guys shipping time. How is his shipping and getting you the parts ordered? 

Have seen some stuff in the past cheaper but went else where  and paid more, just because his was  was coming that far.
REDNECK Saw Repair Getter Done

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: 372 rings
« Reply #6 on: December 10, 2011, 05:53:09 pm »
I get my stuff from him in a week. If i order on a monday, i get my stuff the next monday. Usually quicker than Baileys. Baileys is 8 days. Unless i use priority ship.
Ron

Offline Old Iron Logging

  • Nitro Hotsaw
  • *******
  • Posts: 1132
  • Karma: 81
Re: 372 rings
« Reply #7 on: December 10, 2011, 05:58:21 pm »
I get alot of parts from him also. Get parts in 1/2 the time it takes to get them from the US. Never had a problem.

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 149
  • Location: Hayesville, NC
Re: 372 rings
« Reply #8 on: December 10, 2011, 06:02:58 pm »
I've bought Caber rings and Meteor pistons from The Greek usually 7-8 days so far.
Shep

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4084
  • Karma: 165
  • OHIO REDNECK
Re: 372 rings
« Reply #9 on: December 23, 2011, 07:00:01 pm »
Not that I am worried about this now. But I wonder IF the Caber or Split rings will hold up to the alky/nitro mix in a race saw or hot gas saw.  ;)

I had some aftermarket 5000 rings that would turn blue and loose compression after a few runs on nitro/alky mix. Only husky partner  OEM rings held up with no problems. 
Now AFM worked fine in gas work saws and a woods ported 5000 still out there and hot woods ported saws, but dont add any coktail mixes.  :-X   Hmmm it blanks out the word cocktail.  :D

I ordered and put 394 OEM rings in the 166 piped saw for this reason when I had aftermarket on hand.

Anyone else found that the aftermarket rings wont hold up to the alky/nitro mix?
REDNECK Saw Repair

 

Related Topics

  Subject / Started by Replies Last post
5 Replies
712 Views
Last post March 31, 2011, 11:33:42 pm
by CSW
5 Replies
709 Views
Last post March 20, 2012, 09:04:51 pm
by Cut4fun .
3 Replies
582 Views
Last post November 06, 2013, 05:35:04 pm
by Captain Howdy
4 Replies
168 Views
Last post February 02, 2014, 07:51:15 am
by fossil
6 Replies
332 Views
Last post July 28, 2019, 12:23:26 pm
by countryhog
0 Replies
85 Views
Last post December 22, 2014, 01:22:11 pm
by Cut4fun .
19 Replies
327 Views
Last post March 07, 2015, 03:22:10 pm
by Eccentric
14 Replies
188 Views
Last post November 24, 2015, 02:27:51 pm
by Cut4fun .
0 Replies
73 Views
Last post October 26, 2016, 02:38:49 pm
by Cut4fun
0 Replies
85 Views
Last post July 16, 2019, 04:27:56 pm
by HUSKY KEV