Author Topic: 365 help needed  (Read 886 times)

0 Members and 50 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23708
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

  • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: 365 help needed
« Reply #10 on: June 13, 2014, 05:51:31 pm »
Do you have a known good carb to swap out. I had a 372 carb I could never figure out that would idle but bog.  Put another carb on it and was good to go.


Offline Old Iron Logging

  • Nitro Hotsaw
  • *******
  • Posts: 1134
  • Karma: 82

  • Total Badges: 31
    Badges: (View All)
    Level 6 Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary
Re: 365 help needed
« Reply #11 on: June 13, 2014, 06:48:10 pm »
Not my saw. Owner said it just started acting this way. When I got it the owner had put a new carb kit in but left out a gasket. I put a new kit in with no change. Then I put a new carb on for the video. Never changed anything. I think coil, but our 2 shop techs say no way. Tried 2 new plugs, no help. Will try a different coil tomorrow.


Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172

  • Total Badges: 25
    Badges: (View All)
    Fourth year Anniversary Third year Anniversary 1000 Posts Second year Anniversary Level 5 500 Posts
Re: 365 help needed
« Reply #12 on: June 13, 2014, 07:37:56 pm »
Sounds like you've taken a fuel issue out of the equation. Pretty much leaves the coil, screwey magnets or slipped flywheel.

One thing I don't understand, is that you say their is no change in the running with the impulse line off?  I've never tried this, but even in a healthy Saw, I don't think the motor would pull fuel all the way from the tank even with the high vacuum on the low side at idle?

Adam

Offline Old Iron Logging

  • Nitro Hotsaw
  • *******
  • Posts: 1134
  • Karma: 82

  • Total Badges: 31
    Badges: (View All)
    Level 6 Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary
Re: 365 help needed
« Reply #13 on: June 13, 2014, 08:28:26 pm »
First I thought it was a bad impulse line. Seen many Stihls that would start on a bad line but not rev up. Started the saw and pulled the line with no change. Going to try switch also.

Offline EHP

  • Gas Hotsaw
  • ******
  • Posts: 637
  • Karma: 80

  • Total Badges: 32
    Badges: (View All)
    Level 6 Linux User Mobile User Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary
Re: 365 help needed
« Reply #14 on: June 14, 2014, 01:40:56 pm »
Art , change the coil , have had 365/372's do the same thing , some will idle perfect but will not gain any rpms . I have seen alot more trouble with the blue coils than the black coils , Have had some blue coils that would idle and when you gave it full throttle it would take 6 to 8 seconds before they would gain rpms but as long as you held the rpms up over 8,000 rpms the saw ran fine

Offline Old Iron Logging

  • Nitro Hotsaw
  • *******
  • Posts: 1134
  • Karma: 82

  • Total Badges: 31
    Badges: (View All)
    Level 6 Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary
Re: 365 help needed
« Reply #15 on: June 14, 2014, 02:01:43 pm »
It was the coil. Put a black one from bil's junked 357 on it. Works fine. Thanks for the help.

Offline jmester

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2106
  • Karma: 171
  • Location: MD

  • Total Badges: 36
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Level 6
Re: 365 help needed
« Reply #16 on: June 14, 2014, 08:52:05 pm »
Glad to hear you got it going.
FEAR NO TREE. FEAR GOD.

 

Related Topics

  Subject / Started by Replies Last post
8 Replies
400 Views
Last post February 06, 2013, 10:56:35 pm
by RoyM
9 Replies
717 Views
Last post May 27, 2013, 06:21:39 pm
by 660magnum
3 Replies
1377 Views
Last post July 31, 2014, 01:06:25 am
by 3000 FPS
0 Replies
157 Views
Last post May 23, 2015, 11:17:43 am
by Cat-Face Timber
7 Replies
670 Views
Last post June 20, 2015, 06:04:48 pm
by Old Iron Logging
0 Replies
130 Views
Last post April 04, 2016, 11:29:33 am
by leec
0 Replies
193 Views
Last post April 07, 2016, 11:51:45 am
by stretch5881
2 Replies
446 Views
Last post January 20, 2017, 12:26:58 am
by pete
6 Replies
471 Views
Last post October 27, 2017, 06:01:54 am
by Al Smith
3 Replies
508 Views
Last post January 01, 2019, 04:03:41 pm
by HolmenTree