Author Topic: 435 Compression  (Read 944 times)

0 Members and 1 Guest are viewing this topic.

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 149
  • Location: Hayesville, NC
435 Compression
« on: February 10, 2016, 09:51:20 am »
Just tore down my first 435.  Saw wouldn't run. Pulled muffler piston looks good thru ex. port.  Looked thru spark plug hole thought I could see scoring between transfers and ex. port.  Did compression check 93 psi.  I had a new PC so I thought I would install it.  Carb removal was interesting to say the least with all the locating tabs on intake boot.  Found the case to cyl base screws 1 missing, 2 loose, 1 tight.  Piston is not scored machine marks still present.  Ring is free and looks good.  Don't have an explanation of low comp.  No decomp valve on this motor.  Question is is it possible on these Xtork motors to loose comp due to vac leak between the base and cyl.?

Placing a Jacks order so will put a new ring ($6.18 @ Jacks).
Shep

Share on Facebook Share on Twitter


Offline gregh

  • 3 cube
  • *
  • Posts: 11
  • Karma: 0
Re: 435 Compression
« Reply #1 on: February 10, 2016, 01:37:52 pm »
Do you still have it opened up. Are able to remove the base on this model?


Mower Tech small engine repair
Joplin, mo

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 149
  • Location: Hayesville, NC
Re: 435 Compression
« Reply #2 on: February 10, 2016, 02:05:19 pm »
Yes it's still open.  Going to do new ring and have to order one.  Can't remove base it's part of plastic crankcase like old Husky WE (like 235R IIRC).
Shep

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4067
  • Karma: 162
  • OHIO REDNECK
Re: 435 Compression
« Reply #3 on: February 10, 2016, 02:14:08 pm »
Never had to open one of these yet. Only tune ups etc.  Any pics? 
REDNECK Saw Repair

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 149
  • Location: Hayesville, NC
Re: 435 Compression
« Reply #4 on: February 10, 2016, 02:48:32 pm »
No pics grandaughter hasn't got home from school.
Shep

Offline Karla48

  • pruner
  • *
  • Posts: 1
  • Karma: 0
Re: 435 Compression
« Reply #5 on: February 20, 2016, 06:03:41 pm »
Great little chainsaws ( the Model 435). I repaired three of them over the last 6 months, I can't remember what was wrong with the first one I think maybe it was a carburetor problem. The second one was a friends who asked,  If I could due a tune-up for it, which I did but the real problem was operator error on his part on how to start it. The third one I repaired recently just had a bad ignition module, and its running again.

Good luck on your re-build  :-*
Karla

 

Related Topics

  Subject / Started by Replies Last post
56 Replies
1261 Views
Last post December 27, 2013, 02:20:57 pm
by 1manband
Compression

Started by ed McCulloch

8 Replies
2424 Views
Last post February 07, 2012, 03:07:10 pm
by Al Smith
43 Replies
421 Views
Last post August 05, 2014, 11:59:23 am
by Mastermind
15 Replies
233 Views
Last post March 07, 2015, 11:29:21 am
by 3000 FPS
6 Replies
275 Views
Last post May 09, 2016, 05:25:47 am
by Al Smith
9 Replies
170 Views
Last post February 22, 2017, 10:41:26 pm
by RoyM
3 Replies
118 Views
Last post June 20, 2017, 09:56:52 pm
by farmboy
9 Replies
209 Views
Last post April 12, 2018, 04:33:45 am
by dano
1 Replies
130 Views
Last post March 08, 2019, 09:18:46 am
by Cut4fun .
8 Replies
193 Views
Last post July 18, 2019, 10:39:45 am
by The Ripper