« previous next »
Pages: 1 [2]   Go Down

Author Topic: 44mm husqvarna 350 upgrade options .  (Read 1303 times)

0 Members and 0 Guests are viewing this topic.

Offline wild262

  • 6 cube
  • ****
  • Posts: 161
  • Karma: 29
Re: 44mm husqvarna 350 upgrade options .
« Reply #10 on: January 26, 2016, 09:22:50 pm »
If I were you I would do it over just to be sure.  I coat everything when I do one of those.  Thin coat on both surfaces after degreasing with alcohol.  Better safe than sorry.   And use some lock-tight on those bottom riser bolts also especially the course thread ones.   Afterward, let it cure out at least 1 day before starting.  Weimiedog has built a lot of these and maybe he can come in and take over where I left off.  Good wrenching partner! :)
Logged

Offline wild262

  • 6 cube
  • ****
  • Posts: 161
  • Karma: 29
Re: 44mm husqvarna 350 upgrade options .
« Reply #11 on: January 26, 2016, 09:29:56 pm »
One more thing.  Make sure you snap that new intake band clamp & kit on the cylinder BEFORE you drop the cyl. down over the piston.  Since your using a gasket I guess its no big deal if you forget, but if using 3-bond or Dirko, it can be a real job to clean off and re-seal. 
Logged

Offline fuzz1500

  • 4 cube
  • **
  • Posts: 35
  • Karma: 5
Re: 44mm husqvarna 350 upgrade options .
« Reply #12 on: January 26, 2016, 10:20:19 pm »
Thanks so much.....I just took it apart and resealed.....should have just done it anyway I guess !
I will take your advice about the intake as well. Thanks so much for your help !
Logged

Offline weimedog

  • 6 cube
  • ****
  • Posts: 260
  • Karma: 57
Re: 44mm husqvarna 350 upgrade options .
« Reply #13 on: January 30, 2016, 12:37:52 am »
Here is a  345 tp 350 open port build with a few tips.

https://www.youtube.com/watch?v=wyVcMZw3Jr0
Logged

Offline raumato01

  • 4 cube
  • **
  • Posts: 37
  • Karma: 2
Re: 44mm husqvarna 350 upgrade options .
« Reply #14 on: March 10, 2016, 03:32:32 am »
I just picked up an oem  346 piston and cylinder for this project, got a couple of other saws to finish first and then get onto this. Has anyone tried the Huztl seals or should I stick with oem?
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22415
  • Karma: 582
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 44mm husqvarna 350 upgrade options .
« Reply #15 on: March 10, 2016, 02:51:43 pm »
I havent tried huztl seals but have tried other aftermarket seals.

Some work good and some dont. = quality control like anything aftermarket. Hit and miss.
Logged
REDNECK Saw Repair Getter Done
Pages: 1 [2]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
5 Replies
560 Views 		Last post August 18, 2011, 10:01:40 am
by Cut4fun .
103 Replies
3740 Views 		Last post February 24, 2014, 05:49:35 am
by 350XP
0 Replies
1125 Views 		Last post April 04, 2012, 12:29:54 pm
by Cut4fun
11 Replies
1127 Views 		Last post May 18, 2012, 10:03:11 pm
by Al Smith
8 Replies
887 Views 		Last post April 16, 2014, 07:38:59 am
by farmboy
4 Replies
192 Views 		Last post December 06, 2013, 01:29:38 am
by AKDoug
51 Replies
1510 Views 		Last post September 12, 2014, 07:41:52 am
by 660magnum
8 Replies
332 Views 		Last post September 07, 2014, 10:24:52 am
by 660magnum
41 Replies
1478 Views 		Last post May 08, 2015, 12:14:40 pm
by aclarke
ms250 oiler upgrade

Started by Mark T « 1 2 » Stihl

11 Replies
713 Views 		Last post April 19, 2015, 09:17:13 pm
by 660magnum