Author Topic: 51 project  (Read 524 times)

0 Members and 0 Guests are viewing this topic.

Offline rgclmc

  • 4 cube
  • **
  • Posts: 35
  • Karma: 1
  • Location: NW Pa
Re: 51 project
« Reply #10 on: January 14, 2012, 03:16:45 pm »
Man of stihl told me that also but I don't know where it lines up, Allthough I guess I could compare it to the other one. I already have another flywheel if I could get the pawls changed over.

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: 51 project
« Reply #11 on: January 14, 2012, 03:44:18 pm »
Cant you see where the molded keyway broke off?
Ron

Offline rgclmc

  • 4 cube
  • **
  • Posts: 35
  • Karma: 1
  • Location: NW Pa
Re: 51 project
« Reply #12 on: January 14, 2012, 03:56:10 pm »
After comparing the two I can tell, but not while its on the crank. If I can find something small and strong enough I think I can bring it to work and use the big vice to press them out. It bums me out that they would take them out to before selling a flywheel. :(

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22183
  • Karma: 560
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 51 project
« Reply #13 on: January 14, 2012, 03:57:55 pm »
If going for stock timing just use permanent marker and mark flywheel and crank. Line up slid on.
REDNECK Saw Repair Getter Done

Offline rgclmc

  • 4 cube
  • **
  • Posts: 35
  • Karma: 1
  • Location: NW Pa
Re: 51 project
« Reply #14 on: January 14, 2012, 04:03:58 pm »
I'll try that and see what I end up with.

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: 51 project
« Reply #15 on: January 14, 2012, 04:11:00 pm »
If going for stock timing just use permanent marker and mark flywheel and crank. Line up slid on.
Thats what i would do. I think i would play with the timing a little too. Advance it a tad & make some timed cuts. ;)
Ron

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 149
  • Location: Hayesville, NC
Re: 51 project
« Reply #16 on: January 15, 2012, 09:08:09 am »
The starter pawl pins knock out from the rear of the flywheel.  Get a punch that fits the hole and smack the heck out of it.  If they don't pop out hit harder.
Shep

 

Related Topics

  Subject / Started by Replies Last post
8 Replies
304 Views
Last post October 05, 2012, 06:37:24 pm
by Al Smith
45 Replies
1989 Views
Last post November 18, 2012, 11:18:43 am
by fatboycowen
5 Replies
388 Views
Last post November 07, 2012, 02:29:23 pm
by H 2 H
33 Replies
1139 Views
Last post February 08, 2013, 11:42:46 am
by 660magnum
37 Replies
826 Views
Last post January 27, 2014, 09:50:32 am
by Tractorsaw1
14 Replies
608 Views
Last post April 22, 2014, 07:35:33 am
by Tractorsaw1
0 Replies
71 Views
Last post February 27, 2017, 10:00:02 pm
by blueberrymuzik
4 Replies
235 Views
Last post November 24, 2017, 12:03:27 pm
by deezlfan
7 Replies
295 Views
Last post April 08, 2018, 09:45:27 am
by deezlfan
3 Replies
127 Views
Last post November 22, 2019, 09:18:33 am
by Cut4fun .