Author Topic: 560XP/562XP have a outboard clutch  (Read 11002 times)

0 Members and 10 Guests are viewing this topic.

Offline w8ye

  • 5 cube
  • ***
  • Posts: 117
  • Karma: 5

  • Total Badges: 14
    Badges: (View All)
    Third year Anniversary Second year Anniversary Level 3 Karma Linux User Combination
Re: 560XP/562XP have a outboard clutch
« Reply #40 on: January 09, 2012, 10:11:51 am »
Front of crankcase



Saw bottom



Saw front with muffler removed



3/4 view of cylinder from the left front



Close up of fillet on crankshaft



Left side of cylinder with intake attached



Looking down on crankcase. Front is to the right


Offline w8ye

  • 5 cube
  • ***
  • Posts: 117
  • Karma: 5

  • Total Badges: 14
    Badges: (View All)
    Third year Anniversary Second year Anniversary Level 3 Karma Linux User Combination
Re: 560XP/562XP have a outboard clutch
« Reply #41 on: January 09, 2012, 10:19:59 am »
ID plate and safety strap on AV



Front 3/4 of saw from RT side



Air box floor from RT side



Spark plug and compression release pockets in cylinder head


Offline w8ye

  • 5 cube
  • ***
  • Posts: 117
  • Karma: 5

  • Total Badges: 14
    Badges: (View All)
    Third year Anniversary Second year Anniversary Level 3 Karma Linux User Combination
Re: 560XP/562XP have a outboard clutch
« Reply #42 on: January 09, 2012, 10:28:47 am »
Cylinder head penthouse from right side?



Farther back



Cylinder 3/4 from RT Frnt



Cylinder from right



Crank assm. PTO left flywheel RT. Notice lubrication hole for clutch bearing




Offline w8ye

  • 5 cube
  • ***
  • Posts: 117
  • Karma: 5

  • Total Badges: 14
    Badges: (View All)
    Third year Anniversary Second year Anniversary Level 3 Karma Linux User Combination
Re: 560XP/562XP have a outboard clutch
« Reply #43 on: January 09, 2012, 10:40:00 am »
Left front lower corner of cylinder looking down through intake port



Bottom of cylinder from front



Another view of cylinder intake port at bottom of cylinder



Right intake port looking into cylinder from outside


Offline w8ye

  • 5 cube
  • ***
  • Posts: 117
  • Karma: 5

  • Total Badges: 14
    Badges: (View All)
    Third year Anniversary Second year Anniversary Level 3 Karma Linux User Combination
Re: 560XP/562XP have a outboard clutch
« Reply #44 on: January 09, 2012, 10:43:12 am »
Carb port on cylinder from inside. Notice the hole for the impulse line and the air ports on each side that align with the pockets in the piston.



Same view from a slightly different angle



View inside cylinder with port to carb on left and exhaust on right. X Torq port and intake transfer port in between



Inside cylinder with exhaust port on right and intake port on left




Offline w8ye

  • 5 cube
  • ***
  • Posts: 117
  • Karma: 5

  • Total Badges: 14
    Badges: (View All)
    Third year Anniversary Second year Anniversary Level 3 Karma Linux User Combination
Re: 560XP/562XP have a outboard clutch
« Reply #45 on: January 09, 2012, 10:58:57 am »
Piston from intake side showing X Torq air channels on both sides



Another view of exhaust port from outside showing finish.



Another view of crankshaft without full circle stuffer plates



Cylinder from left side with intake attached



Where carb attaches


Offline w8ye

  • 5 cube
  • ***
  • Posts: 117
  • Karma: 5

  • Total Badges: 14
    Badges: (View All)
    Third year Anniversary Second year Anniversary Level 3 Karma Linux User Combination
Re: 560XP/562XP have a outboard clutch
« Reply #46 on: January 09, 2012, 11:05:56 am »
Looking up through ports of cylinder



Looking at Strato passage on side of piston



Strato passages on sides of piston



Ring pin in piston


Offline w8ye

  • 5 cube
  • ***
  • Posts: 117
  • Karma: 5

  • Total Badges: 14
    Badges: (View All)
    Third year Anniversary Second year Anniversary Level 3 Karma Linux User Combination
Re: 560XP/562XP have a outboard clutch
« Reply #47 on: January 09, 2012, 11:12:47 am »
Inside of piston showing reduced area because of Strato passages on outside



Side view of piston



Crankcase with piston



Crankcase muffler area from flywheel side


Offline w8ye

  • 5 cube
  • ***
  • Posts: 117
  • Karma: 5

  • Total Badges: 14
    Badges: (View All)
    Third year Anniversary Second year Anniversary Level 3 Karma Linux User Combination
Re: 560XP/562XP have a outboard clutch
« Reply #48 on: January 09, 2012, 11:21:22 am »
Crank assembly with full circle stuffers along side



Port passage in crankcase



Looking down in crankcase



Small crankcase volume?


Offline w8ye

  • 5 cube
  • ***
  • Posts: 117
  • Karma: 5

  • Total Badges: 14
    Badges: (View All)
    Third year Anniversary Second year Anniversary Level 3 Karma Linux User Combination
Re: 560XP/562XP have a outboard clutch
« Reply #49 on: January 09, 2012, 11:29:01 am »
Piston top with flame travel and port shadow image



Combustion chamber  is machined



Carb and air induction assembly



Muffler



Piston from right side




 

Related Topics

  Subject / Started by Replies Last post
30 Replies
8790 Views
Last post February 18, 2012, 09:03:13 pm
by mdavlee
48 Replies
7060 Views
Last post January 26, 2013, 05:48:22 pm
by brokenbudget
5 Replies
1734 Views
Last post June 17, 2012, 06:08:07 am
by mountainlake
0 Replies
488 Views
Last post July 22, 2012, 01:08:50 pm
by Cut4fun
15 Replies
2389 Views
Last post January 14, 2013, 01:19:01 pm
by mweba
25 Replies
2817 Views
Last post March 15, 2014, 12:24:09 pm
by KilliansRedLeo
230 Replies
12369 Views
Last post February 18, 2023, 08:34:43 am
by Cut4fun
8 Replies
968 Views
Last post November 13, 2018, 11:41:46 am
by Cut4fun .
7 Replies
1663 Views
Last post November 19, 2020, 08:40:48 pm
by Derf
6 Replies
687 Views
Last post January 11, 2022, 03:12:02 pm
by Tys78