Author Topic: T540xp 562 560 555  (Read 7180 times)

0 Members and 0 Guests are viewing this topic.

Offline mweba

  • Piped Saw
  • *****
  • Posts: 392
  • Karma: 55
Re: 562xp 560xp 555 T540xp
« Reply #60 on: September 29, 2011, 10:19:14 pm »
Carb is a double venturi design.  Also, there are no adjustments on it.  Not even a idle set screw.  Idle and high side rpm are completely electronic controlled.


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22135
  • Karma: 552
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 562xp 560xp 555 T540xp
« Reply #61 on: September 29, 2011, 10:33:20 pm »
Wonder if the carb would adjust for a muffler mod or if someone ported one.
REDNECK Saw Repair Getter Done

Offline mweba

  • Piped Saw
  • *****
  • Posts: 392
  • Karma: 55
Re: 562xp 560xp 555 T540xp
« Reply #62 on: September 29, 2011, 11:06:24 pm »
If it is the same set tup as the 576, it should compensate just fine.

Made a vid of it pulled down.  Kind of shaky but its free so.....lol

http://www.youtube.com/watch?v=stsm7CIuRcc

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22135
  • Karma: 552
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 562xp 560xp 555 T540xp
« Reply #63 on: September 30, 2011, 09:18:14 am »
Is this the first husky to start using the molded fuel lines like stihl or did I miss that on the 576 etc?

Thanks for everything. Thats what this site is all about, sharing and FREE.  ;D
REDNECK Saw Repair Getter Done

Offline mweba

  • Piped Saw
  • *****
  • Posts: 392
  • Karma: 55
Re: 562xp 560xp 555 T540xp
« Reply #64 on: September 30, 2011, 08:24:46 pm »
I believe it is the first but not sure.

Stock 555 vs stock 357.

http://www.youtube.com/watch?v=bMTZJaecEkw


http://www.youtube.com/watch?v=cdSwlY3Rdbc

Offline mdavlee

  • 5 cube
  • ***
  • Posts: 138
  • Karma: 4
Re: 562xp 560xp 555 T540xp
« Reply #65 on: September 30, 2011, 10:29:22 pm »
The autotune will compensate for a muffler mod on the 576. I've got one now on it's way to the gtg in tn tomorrow. Andre and Nik have been playing with it and a 441 m tronic some the past few weeks.

http://www.youtube.com/watch?v=WcYSHLwx3yU

Offline SawTroll

  • Nitro Hotsaw
  • *******
  • Posts: 1196
  • Karma: 68
  • Information collector
  • Location: Troms, North Norway
Re: 562xp 560xp 555 T540xp
« Reply #66 on: October 01, 2011, 04:31:39 pm »
The 562xp has started hitting dealers, at least in Maine, so why discussing the lesser 555 -  ;D

Ok, the 555 is the replacement for the 359, and obviously a better saw!  8)

Offline John Mc

  • 5 cube
  • ***
  • Posts: 133
  • Karma: 13
  • Location: Addison Co, VT
Re: 562xp 560xp 555 T540xp
« Reply #67 on: October 02, 2011, 10:40:41 am »
As near as I can tell from the video, the 555 beats the 357XP by a couple of seconds... 12 seconds vs 14 seconds per cut.

I assume chains were in similar shape?

Offline mweba

  • Piped Saw
  • *****
  • Posts: 392
  • Karma: 55
Re: 562xp 560xp 555 T540xp
« Reply #68 on: October 02, 2011, 03:57:23 pm »
Bar and chain were swapped one saw to the other.  Exactly the same.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22135
  • Karma: 552
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 562xp 560xp 555 T540xp
« Reply #69 on: October 02, 2011, 04:01:45 pm »
Good deal. I was hoping that is what you was going to tell us.   8)

Thanks for sharing info.
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
91 Replies
4541 Views
Last post December 18, 2016, 12:54:06 pm
by Cut4fun .
1 Replies
143 Views
Last post December 01, 2015, 11:24:23 pm
by Cut4fun .