« previous next »
Pages: [1]   Go Down

Author Topic: Aftermarket Cylinder kit for 268 with interesting timing numbers.  (Read 519 times)

0 Members and 0 Guests are viewing this topic.

Offline weimedog

  • 6 cube
  • ****
  • Posts: 260
  • Karma: 57
Aftermarket Cylinder kit for 268 with interesting timing numbers.
« on: January 22, 2014, 09:29:56 am »
Building a saw with an aftermarket Cylinder kit....an open port 268 top end from an Asian source. Put it together and measured things.....

With NO base gasket:

Squish .017"
Intake: 76 degrees BTDC
Exhaust: 103 degrees After TDC
Transfers: 132 degrees ATDC

Blow down.....29 degrees???

Going to run it as built....the way most would in the same situation. Curious what that long blow down will do and is it worth bringing it to the 25 degree range. Would be a PITA! Might be able to get a couple of degrees modding the piston crown w/o killing it.... ::)
Logged

Share on Facebook Share on Twitter

Offline winland

  • 6 cube
  • ****
  • Posts: 215
  • Karma: 24
  • Location: 44883
    • Winland Boxers
Re: Aftermarket Cylinder kit for 268 with interesting timing numbers.
« Reply #1 on: January 22, 2014, 09:47:13 am »
Quote from: weimedog on January 22, 2014, 09:29:56 am

With NO base gasket:

Intake: 76 degrees BTDC
Exhaust: 103 degrees After TDC
Transfers: 132 degrees ATDC

Blow down.....29 degrees???

Do not want to hi-jack but is there someplace I can learn what these numbers mean and how they are measured?
I thank you for your knowledge.
Logged
Like Like x 1 View List

Offline srcarr52

  • 6 cube
  • ****
  • Posts: 288
  • Karma: 94
  • Location: IA
Re: Aftermarket Cylinder kit for 268 with interesting timing numbers.
« Reply #2 on: January 22, 2014, 10:03:33 am »
Long blowdown will hurt upper end HP.  I wouldn't mess with the piston crown for transfer timing as it will hurt the loop scavenging flow.
Logged

Offline danders

  • 3 cube
  • *
  • Posts: 7
  • Karma: 0
Re: Aftermarket Cylinder kit for 268 with interesting timing numbers.
« Reply #3 on: January 22, 2014, 10:25:29 am »
I get the part about a high blowdown limiting rpm but I'm not understanding what loop scavanging is. Does it have to do with the angle of flow coming out of the transfer?
Logged

Offline srcarr52

  • 6 cube
  • ****
  • Posts: 288
  • Karma: 94
  • Location: IA
Re: Aftermarket Cylinder kit for 268 with interesting timing numbers.
« Reply #4 on: January 22, 2014, 12:48:59 pm »
Yes, angling the piston could interfere with the way the new a/f flow into the cylinder and could disrupt the whole process. 
Logged

Offline danders

  • 3 cube
  • *
  • Posts: 7
  • Karma: 0
Re: Aftermarket Cylinder kit for 268 with interesting timing numbers.
« Reply #5 on: January 22, 2014, 02:46:36 pm »
Okay, that makes sense to me. Thanks

To the OP - it's nice to see am kits with a tight squish; a little compression should add some grunt to the saw. See what it runs like as-is before altering the transfers, you may like it well enough not to bother with it.
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
12 Replies
1010 Views 		Last post January 26, 2012, 09:09:40 am
by ECpirates96
4 Replies
756 Views 		Last post August 02, 2012, 04:06:14 pm
by splitpost
5 Replies
1167 Views 		Last post January 18, 2013, 03:51:05 pm
by 660magnum
6 Replies
664 Views 		Last post June 25, 2014, 11:06:00 pm
by aclarke
21 Replies
1502 Views 		Last post November 29, 2014, 08:29:17 am
by weimedog
12 Replies
666 Views 		Last post December 15, 2014, 05:25:46 am
by Eccentric
5 Replies
913 Views 		Last post October 30, 2015, 04:48:09 pm
by dboyd351
8 Replies
497 Views 		Last post December 22, 2015, 12:16:44 pm
by waynec
2 Replies
1500 Views 		Last post March 20, 2016, 01:15:19 pm
by 660magnum
0 Replies
171 Views 		Last post December 22, 2022, 07:56:33 am
by Cut4fun