« previous next »
Pages: [1]   Go Down

Author Topic: Auto-tune or not  (Read 285 times)

0 Members and 0 Guests are viewing this topic.

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Auto-tune or not
« on: December 09, 2013, 08:22:13 pm »
I have a friend who has a 576xp that was made in 2011 34th week. Does not appear to be an AT but I have not seen it up close. So, is there a way or something I could tell him to look at that would show it to be or not to be an AT? The reason I ask is that XP, EPA, and AT saws were made in 2011!
Logged
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Share on Facebook Share on Twitter

Offline Philbert

  • Gas Hotsaw
  • ******
  • Posts: 563
  • Karma: 75
Re: Auto-tune or not
« Reply #1 on: December 09, 2013, 08:26:05 pm »
Are there holes / screws to adjust the carb?

Philbert
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22584
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Auto-tune or not
« Reply #2 on: December 09, 2013, 08:30:09 pm »
I ran a carbed 576 demo saw.  Before they were autotune versions.   Wires to carb area maybe?   ??? :-\
Logged
REDNECK Saw Repair Getter Done

Offline mdavlee .

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1968
  • Karma: 171
Re: Auto-tune or not
« Reply #3 on: December 09, 2013, 08:54:57 pm »
No holes for a screwdriver is the quickest way to see.
Logged

Offline Magnus

  • 6 cube
  • ****
  • Posts: 237
  • Karma: 26
  • Location: Sweden
    • Chainsaw Collectors Forum
Re: Auto-tune or not
« Reply #4 on: December 10, 2013, 10:24:45 am »
Autotune system combined with these new initions is best system so far IMO.
If they would have it on a conventional engine it would be perfect!

Bigger problem IMO is the engine type.
I said it before and have not seen anything to change my opinion
Logged
Chainsaw nut!

Offline HolmenTree

  • Nitro Hotsaw
  • *******
  • Posts: 1378
  • Karma: 195
  • Location: Manitoba Canada
Re: Auto-tune or not
« Reply #5 on: December 11, 2013, 10:36:32 am »
Here's a pic of a 2009 576XP AutoTune I use to have.
 Also another pic that  [I don't have a program to shrink under 400 to post here] so emailed to Kevin to post. In this pic if you zoom up close to the decal on the rewind housing you can see it has "AutoTune" printed in plain view.
Logged
Making a living with a saw since age 16.

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: Auto-tune or not
« Reply #6 on: December 11, 2013, 10:48:44 am »
Thanks guys I mailed the pic from three to my buddy in MS!
Logged
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22584
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Auto-tune or not
« Reply #7 on: December 11, 2013, 12:46:56 pm »
Quote from: HolmenTree on December 11, 2013, 10:36:32 am
Here's a pic of a 2009 576XP AutoTune I use to have.
 Also another pic that  [I don't have a program to shrink under 400 to post here] so emailed to Kevin to post. In this pic if you zoom up close to the decal on the rewind housing you can see it has "AutoTune" printed in plain view.
Logged
REDNECK Saw Repair Getter Done

Offline Magnus

  • 6 cube
  • ****
  • Posts: 237
  • Karma: 26
  • Location: Sweden
    • Chainsaw Collectors Forum
Re: Auto-tune or not
« Reply #8 on: December 11, 2013, 01:06:18 pm »
First Autotune I have seen was put in 570/575's. I had a sneak peak in HVA factory.
There was one test run on 455/460 too I think..
One they tested on 357 too that never got out.
Logged
Chainsaw nut!
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
7 Replies
858 Views 		Last post July 24, 2012, 03:35:33 pm
by Cut4fun .
54 Replies
988 Views 		Last post September 17, 2013, 09:34:04 pm
by kr5258
9 Replies
296 Views 		Last post August 30, 2014, 02:29:35 pm
by Philbert
4 Replies
204 Views 		Last post April 09, 2015, 05:59:35 pm
by 660magnum
13 Replies
75 Views 		Last post November 24, 2017, 06:52:46 pm
by ray benson
23 Replies
439 Views 		Last post July 30, 2015, 08:36:47 am
by John Mc
3 Replies
296 Views 		Last post June 30, 2015, 07:11:44 pm
by Jason K
8 Replies
390 Views 		Last post March 17, 2016, 08:19:59 pm
by 660magnum
2 Replies
305 Views 		Last post December 26, 2016, 05:32:01 pm
by SawTroll
0 Replies
164 Views 		Last post October 23, 2016, 03:14:17 pm
by Cut4fun .